Engineering
Magnet Engineering Support
Send the application, not just the part number. The duty conditions decide the grade, the shape decides the machining, and the coating decides whether either survives the service environment.
How an engineering review runs
Five stages from the application brief to a released production run.
Share the application
Working gap, circuit geometry, operating temperature, environment and how the part is held. A sketch of the assembly is worth more than a part number.
Circuit review
We size the magnet against the duty: grade against temperature, working point against demagnetisation margin, shape against the force the circuit needs.
Written recommendation
You get the proposed grade, shape, coating and magnetisation, with the reasoning and the expected performance, before anything is quoted.
Sample validation
First articles are measured and reported so the assumption can be checked in your assembly, not only on paper.
Production release
Once the sample is approved, the quality plan fixes the controlling dimensions and the acceptance limits for the run.
What we review on your drawing
Most field problems trace back to something visible on the drawing. These are the checks that catch them before the steel is cut.
- Operating temperature against grade: what the base range covers, and what the H, SH, UH, EH and AH classes buy
- Demagnetisation margin at the working point, not only at the catalogue figure
- Magnetisation direction against how the part is held, loaded and assembled
- Coating against the service environment: humidity, salt, wash-down, temperature
- Tolerances against what pressing, sintering and grinding can hold on the shape in question
- Assembly method: adhesive, fastener, housing or press fit, and what each does to the flux path

Selection
Questions we help you answer
The ones that decide whether the part works in service.
- What holding or pull force the assembly will really deliver, against the catalogue figure measured on clean mild steel
- How much temperature margin is prudent for a sealed motor or a sensor in a hot enclosure
- Whether multipole magnetisation helps the sensor or motor circuit, and what it costs per part
- Which coating survives salt fog, wash-down or a humid warehouse, and what it does to the controlling dimension
- How thin a disc can go before the working point, and the real ceiling, drop below the published grade figure
Before You Ask
What to send with the application
Five inputs let the review start the same day.
| Circuit or assembly sketch | Geometry, working gap and how the magnet is held; a photo of the assembly is enough to start |
|---|---|
| Operating temperature | Peak and continuous, at the magnet rather than at the housing surface |
| Environment | Humidity, salt, wash-down, chemicals, vibration |
| Force, torque or flux target | Whatever the circuit has to deliver, with the measurement it is judged against |
| Volume and schedule | Prototype quantity and annual volume, which decide tooling |
Documents available on request
Engineering documents we share during a project — request the current version from our team.
Go Deeper
Related reading
- Polarity and magnetisation direction — how the pole pattern is set and inspected
- Remanence versus coercivity — the two numbers that size a magnetic circuit
- Neodymium temperature limits — what each temperature class buys and where it stops
- High-temperature neodymium magnets — how dysprosium and terbium raise the ceiling
- Pull force versus breakaway force — why the catalogue number and the real one differ
Buyer Questions
Engineering Support FAQs
Do you run magnetic circuit calculations?
Yes. Send the working gap, the circuit geometry and the operating temperature and we size the magnet, report the expected flux and force, and confirm it on a sample.
Can you recommend a grade from a temperature figure alone?
Temperature is the main driver, but the working point and the permitted demagnetisation margin matter as much. Send both and we will size the grade.
What if the drawing cannot be made as drawn?
We flag the feature, propose the closest manufacturable alternative and re-quote before anything is cut. Nothing is machined on an assumption.
Do you support prototype quantities?
Yes. Prototype runs are a normal part of a custom project, and the sample is measured and reported like a production batch.
Is engineering support chargeable?
The review that comes with a quotation is part of the service. Standalone development work is quoted separately, and the scope is agreed before it starts.
Send us the requirement
Tell us the application, the duty and the quantity. You get a specification, a schedule and a quote in writing.
Request a quote