Standard NdFeB grades are rated to about 80℃. Push beyond that and the magnet begins to lose flux permanently, so for hotter duty a different branch of the family is needed. High temperature neodymium magnets use a suffix system - M, H, SH, UH, EH and AH - that raises the maximum operating temperature in steps from 100℃ up to 230℃. This article explains how the suffixes map to temperature, why the trade-off works the way it does, and how to pick the series for your heat load.
The temperature suffix system
The published sintered NdFeB table organises temperature-rated grades into six tiers, each defined by its maximum operating temperature:
- M series - 100℃
- H series - 120℃
- SH series - 150℃
- UH series - 180℃
- EH series - 200℃
- AH series - 230℃
Within each tier you will find a spread of energy-product levels. For example the M tier includes 42M, 48M, 50M, 52M and 55M; the H tier includes 42H through 55H; the SH tier runs from 38SH up to 54SH; the UH tier from 30UH to 52UH; the EH tier from 30EH to 50EH; and the AH tier from 28AH to 42AH. The prefix number still denotes the energy-product band, so a 42M and a 42H share a similar (BH)max but differ in their heat rating.
Why higher temperature costs energy product
Raising the operating temperature means raising the magnet's coercivity so it resists demagnetisation as thermal energy works against the magnetic domains. Achieving that coercivity typically comes at the expense of remanence and energy product. The table shows the trade plainly: a 38SH is rated to 150℃ but its (BH)max band is 35-40 MGOe, below the 39-44 MGOe of a standard N42, and a 28AH rated to 230℃ falls to 25-30 MGOe. In other words, the hotter the service, the more you give up in raw field strength.
Matching the series to the duty
Choosing the series is a matter of specifying the lowest tier that covers your worst-case temperature, rather than the highest available. Overspecifying buys coercivity you do not need and surrenders energy product you might. A practical guide:
- Around 100-120℃: M or H series for mild under-bonnet or equipment-in-enclosure duty
- 130-150℃: SH series for automotive and industrial hotspots
- 160-180℃: UH series for deeper under-hood or process heat
- 190-200℃: EH series for demanding drivetrain or geothermal-adjacent duty
- up to 230℃: AH series for the most extreme sustained heat
Always confirm the number against the magnet's actual working point. The maximum operating temperature assumes a reasonable magnetic circuit; a magnet driven far into saturation or subjected to strong opposing fields will demagnetise at a lower temperature than the rating suggests.
A worked comparison
Consider a design that must survive 150℃. A standard N42 (80℃) is out of its depth there, but a 42SH is rated to exactly 150℃ while keeping a 39-44 MGOe band - essentially the same strength as N42 but heat-rated. If the same part were pushed to 180℃, you would step to a 42UH, and at 230℃ to a 42AH, each time trading a little energy product for the needed coercivity. The lesson is to let the temperature, not the catalogue's strongest number, drive the suffix.
Coating still matters at temperature
Heat accelerates corrosion and can soften some plating systems, so the finish must be chosen for both chemistry and temperature. The coating table lists working-temperature limits for each finish - nickel-copper-nickel and the epoxy systems are rated to around 200℃, while some zinc and epoxy variants are limited to 160℃. Pair the temperature series with a coating whose own limit clears your service temperature, and confirm magnetisation direction and tolerance at enquiry.
Working with a supplier
Specifying a high-temperature magnet means stating the service temperature, the duty cycle and the working point, not just the suffix. YUECI KEJI supplies the full M through AH range and can model the circuit so the chosen tier is the lowest that safely covers the heat. For the standard grades, see the NdFeB magnet overview.
Temperature is not just a number
The 80, 100, 120, 150, 180, 200 and 230℃ figures assume a sensible magnetic circuit. A magnet driven deep into saturation, or exposed to a strong opposing field from neighbouring steel or another magnet, will demagnetise at a lower temperature than its rating suggests. For critical duty, ask the supplier to confirm the permissible operating temperature at your specific working point rather than quoting the grade ceiling.
Common misapplications
The usual error is fitting a standard N grade into a hot environment because the initial pull looked fine at room temperature, only to lose flux after a few heat cycles. The second is overspecifying to AH "just to be safe" and giving up large amounts of energy product the design never needed. Both are avoided by matching the tier to the measured worst-case temperature and duty cycle.
Coating and temperature together
For hot duty the coating is a second temperature limit on top of the grade. A 200℃ epoxy or Ni-Cu-Ni finish pairs with most high-temperature grades, while a 160℃ finish would cap an SH or UH part well below its magnetic rating. Read the coating table and the grade table as one combined limit.
Documenting the choice
Record the service temperature, the duty cycle and the chosen tier in the design file so future revisions do not accidentally drop to a cheaper standard grade. A magnet qualified at 150℃ with 42SH should not quietly become N42 in a cost-cutting pass, because the demagnetisation risk returns.
Summary of the tiers
To recap: M at 100℃, H at 120℃, SH at 150℃, UH at 180℃, EH at 200℃ and AH at 230℃. Pick the lowest tier that covers the worst-case temperature, pair it with a coating whose own limit clears the service temperature, and confirm the working point with the supplier. That three-step routine prevents both demagnetisation and over-specification.
Closing thoughts
The temperature tiers exist because heat is the enemy of permanent magnetism in neodymium. Respecting the 80 to 230℃ ladder is the difference between a magnet that lasts and one that quietly fails after a few hot cycles, so treat the tier as a design input from the start rather than a fix applied after the fact.
Frequently asked questions
What does the "SH" in 42SH mean? The suffix marks the temperature tier - SH denotes a maximum operating temperature of 150℃ - while "42" is the energy-product band, here 39-44 MGOe.
Why is a high-temperature grade weaker than a standard grade? Higher operating temperature requires higher coercivity, which is usually achieved at the expense of remanence and energy product; a 28AH at 230℃ reaches only 25-30 MGOe.
Can I just use N52 everywhere and accept some heat loss? No. Above 80℃ a standard N grade risks irreversible demagnetisation; for sustained heat you must use the rated M/H/SH/UH/EH/AH series.
Does the coating limit the temperature too? Yes. Each finish has its own working-temperature rating, so the assembly is limited by the lower of the magnet grade and the coating.
How do I pick the lowest sufficient tier? State your worst-case service temperature and duty cycle; the supplier can then recommend the lowest suffix that covers it without surrendering unnecessary energy product.
If your product runs hot and you need the right temperature series and coating, Request a quote with the service temperature and duty cycle so the grade can be matched correctly.