For applications that must pull hard from a small volume but still run at normal temperatures, the N48 neodymium magnet is a workhorse of high-energy design. Sitting near the top of the standard NdFeB range, it offers a 45-50 MGOe energy product that lets engineers shrink magnets or raise force without stepping into the most expensive top grades. This article sets out the N48 specification, what the numbers mean, and the designs that benefit most.
N48 specification
The published sintered NdFeB band for N48 is:
- Remanence (Br): 1.37-1.42 T (13.7-14.2 kGs)
- Intrinsic coercivity (Hcj): at least 12 kOe (955 kA/m)
- Magnetic coercivity (Hcb): at least 11.2 kOe (892 kA/m)
- Maximum energy product ((BH)max): 45-50 MGOe (358-398 kJ/m³)
- Maximum operating temperature: 80℃
As with N42 and N45, the intrinsic coercivity floor stays at 955 kA/m, so the gain over lower grades is in remanence and energy product rather than demagnetisation resistance. The magnet simply holds and delivers more flux per unit volume.
What the numbers tell a designer
Remanence of 1.37-1.42 T is the residual field after magnetisation, and the 45-50 MGOe band is the peak of the demagnetisation curve. In a real circuit the magnet operates somewhere down that curve at its working point, so the useful figure is the flux density at your load line. A higher energy product lets you either shrink the volume for the same force or raise the force in the same volume - the two ways high-energy grades earn their premium.
Where N48 earns its premium
Moving from N42 to N48 raises the energy product from 39-44 to 45-50 MGOe. That is a meaningful gain when volume is the binding constraint. N48 is commonly chosen for:
- High-torque, space-limited motors and generators
- Magnetic couplings that must transmit more torque in the same bore
- Precision sensors and encoders needing a strong, stable bias field
- Miniaturised actuators, medical devices and instruments
- High-field clamps and fixtures where mass must stay low
In each case the designer trades a little extra material cost for a smaller, stronger magnet - often the cheaper route once you account for the saved steel, housing and assembly space.
N48 versus the grades around it
N45 (42-47 MGOe) is the cheaper neighbour when the extra few points are not decisive. N50 (47-52 MGOe) and the top grades N52-N58 push further but usually at a higher price and tighter process control. N48 is the pragmatic high-energy choice: strong, widely available, and still on the standard 80℃ production route rather than a specialist line.
Coating and assembly care
All sintered NdFeB is hard, brittle and susceptible to corrosion without protection, and N48 is no exception. Nickel-copper-nickel is the usual indoor finish; zinc or epoxy systems are specified for humidity, salt spray or chemical service. Because N48 magnets are often small and highly loaded, the coating thickness and edge coverage matter - thin or chipped plating is the usual route to field failures, so finish selection should follow the duty cycle, not just the catalogue. Confirm the magnetisation direction and tolerance at enquiry.
Working with a supplier
When you specify N48, the grade is only half the story; the working point, shape and coating decide the outcome. YUECI KEJI supplies N48 in discs, rings, blocks and arcs with a quality system aligned with IATF16949 and ISO 9001/14001/45001, and can model the magnetic circuit so the part is matched to the real load. See the NdFeB magnet overview for the broader family.
Designing safely with high energy product
A 45-50 MGOe magnet is small and heavily loaded, which raises two practical risks. First, small NdFeB parts chip and crack easily if they snap together or against steel, so handling and automated assembly need controlled presentation. Second, because the field is strong, the magnetisation direction and any multi-pole pattern must be exact, since a mis-oriented pole wastes most of the available force. Plan the fixture and the coating together, not separately.
N48 in motors versus sensors
In motors the grade buys torque per volume and lets the rotor shrink; in sensors it buys a steadier, stronger bias field that improves signal-to-noise. The same 45-50 MGOe serves both, but the tolerance and magnetisation pattern differ, so specify the end use so the right variant is supplied.
Why high energy product changes the assembly
When you shrink a magnet using a 45-50 MGOe grade, the surrounding steel, housing and even the adhesive gap often need re-optimisation, because the field is now stronger and more localised. Designers who upgrade the grade but leave the rest of the magnetic circuit unchanged sometimes see little benefit; the gain is realised only when the whole path is revisited.
Magnets, not magic
A high grade does not compensate for a poor circuit. The most reliable way to hit a force target is to model the working point and confirm the magnet operates on the linear part of its curve, then choose N48 if the volume must stay small. Treating grade selection as the first step rather than the only step avoids disappointed expectations.
Quality and consistency at N48
Because the energy product band is high in the standard range, small variations in processing move the lot within the band; for critical assemblies ask for the actual curve and a tighter tolerance. YUECI KEJI supplies N48 with a quality system aligned with IATF16949 and ISO 9001/14001/45001 so lot-to-lot behaviour is documented.
Recycling and material value
Because high-energy NdFeB contains valuable rare earths, end-of-life recovery is increasingly part of the sourcing conversation. Specifying N48 does not change the recovery route, but buyers with sustainability requirements should ask how scrap and returns are handled, since a supplier with a documented take-back or recycling path reduces both cost and compliance risk over the product life. For the broader grade picture, see the high-temperature guide and the NdFeB overview.
Reviewing the N48 choice
A quick sanity check before committing: confirm the volume truly must stay small, confirm the circuit is modelled, and confirm the coating suits the environment. If all three hold, N48 is a sound, economical high-energy choice; if any fails, a different grade or a circuit change will serve better than forcing N48 into a role it does not fit.
Frequently asked questions
How much stronger is N48 than N42? Its energy product runs 45-50 MGOe against 39-44 MGOe, roughly a 10-14 percent gain that translates directly into more flux or a smaller part for the same force.
Is N48 safe above room temperature? The standard N grade is rated to 80℃ maximum operating temperature. Sustained higher temperatures require a temperature-rated series such as H, SH, UH, EH or AH.
Does N48 resist demagnetisation better than N42? The intrinsic coercivity floor is the same 955 kA/m across these standard grades, so raw demagnetisation resistance is comparable; N48 simply delivers more field.
What finish should I choose for N48? Ni-Cu-Ni for general indoor use, epoxy or thicker zinc where humidity or chemicals are present, always matched to the actual environment.
Is N48 harder to source than N42? It is a well-established, widely produced grade rather than a niche one, so lead times are generally comparable; confirm at enquiry for custom geometries.
To size an N48 magnet for your envelope and load, Request a quote and share the working point or a drawing so the geometry and coating can be matched.