GRADES

N45 Neodymium Magnet: A Step Up in Energy Product | YUECI KEJI

When a design is squeezed for space but cannot afford the cost or supply risk of the very top grades, the N45 neodymium magnet is a frequent answer. It carries roughly seven percent more maximum energy product than N42 while staying on the same economical, well-established production route.

When a design is squeezed for space but cannot afford the cost or supply risk of the very top grades, the N45 neodymium magnet is a frequent answer. It carries roughly seven percent more maximum energy product than N42 while staying on the same economical, well-established production route. This article covers the N45 specification, how to read it, and the situations where that modest step up earns its keep.

N45 at a glance

From the sintered NdFeB material table, the published N45 band is:

  • Remanence (Br): 1.32-1.38 T (13.2-13.8 kGs)
  • Intrinsic coercivity (Hcj): at least 12 kOe (955 kA/m)
  • Magnetic coercivity (Hcb): at least 11.0 kOe (876 kA/m)
  • Maximum energy product ((BH)max): 42-47 MGOe (334-374 kJ/m³)
  • Maximum operating temperature: 80℃

The coercivity floor of 955 kA/m is identical to N42, so demagnetisation resistance does not change as you move up to N45. What changes is the remanence and the energy product: the magnet holds a slightly stronger residual field and can deliver more flux from the same volume.

Why a small step up matters

A jump from 39-44 MGOe to 42-47 MGOe sounds minor on paper, but in a tight magnetic circuit it can mean the difference between meeting a pull-force target and missing it. Designers often reach for N45 when:

  • A package must shrink but the force budget is fixed
  • A slightly stronger bias field improves sensor signal or motor torque
  • The part count or magnet volume needs to drop to hit a cost target
  • A thinner wall or lighter moving part is required for inertia reasons

Because N45 sits close to N42 on the production curve, the price delta is usually modest, which is why it is a popular "better than baseline" choice rather than a specialist grade.

Reading the numbers

Remanence of 1.32-1.38 T is the residual induction, the field the magnet keeps after magnetisation. The energy product band of 42-47 MGOe is the headline, but for a working design the relevant quantity is the flux available at the operating point, not the peak of the curve. A supplier can plot the demagnetisation curve for the specific lot so you can confirm the field at your load line rather than quoting the grade alone.

N45 versus neighbouring grades

Below N45, N42 is the cheaper, slightly weaker default. Above it, N48 and N50 push energy product to 45-50 and 47-52 MGOe, gaining more force per volume at a steeper cost. N45 is the middle rung: enough extra performance to matter, not enough to push into the premium tier. For most ambient-temperature products that simply need "a bit more than baseline", N45 is the efficient pick.

Typical applications

N45 suits the same broad families as N42 but where the extra energy product is exploited:

  • Compact motors and micro-actuators where every cubic millimetre of magnet counts
  • Thinner magnetic latches, clasps and holding assemblies
  • Magnetic couplings and separators tuned for a higher field in the same envelope
  • Speaker and transducer pole pieces where a stronger gap field improves output
  • Precision instruments and meters needing a steadier bias field

Coating and handling

N45 shares the material character of the whole NdFeB family: hard, brittle and corrosion-prone if bare. A protective finish is standard. Nickel-copper-nickel plating is the common default for indoor and general use, with zinc or epoxy selected for humidity, salt-spray or chemical exposure. Respect both the 80℃ magnet limit and the coating's own temperature rating when specifying the finish, and confirm the magnetisation direction matches the assembly.

Working with a supplier

When specifying N45, give the supplier the working point and the magnetisation direction as well as the grade, because those determine whether the part actually delivers the force you calculated. YUECI KEJI supplies N45 across disc, ring, block and arc geometries and can model the circuit so the grade is matched to the load rather than guessed. See the NdFeB magnet overview for the full family.

When N45 is not the answer

N45 is a sensible upgrade from N42, but it is not universal. If the assembly runs above 80℃, the standard N45 is the wrong branch entirely and a temperature-rated series is required. If volume is no constraint and cost dominates, N42 or even a lower grade is the economical pick. And if the design genuinely needs maximum pull from a tiny envelope, N48 or N50 will serve better than squeezing N45. Using N45 where a simpler or stronger grade fits only adds cost without benefit.

A short cost-performance note

Because N45 sits close to N42 on the production route, the material premium is usually small, which is why it is popular as a default "a bit better" choice. The real saving comes from what the extra energy product lets you remove - less steel, a thinner wall, a smaller housing - so evaluate N45 at the system level rather than the magnet line item alone.

Reading an N45 quote

A useful quote states not just "N45" but the shape, the magnetisation direction, the coating and the tolerance, plus the demagnetisation curve for the lot. Without those, two "N45" parts from different sources can behave differently in the same circuit. Treat the grade as one of several specifications, not the whole order.

Pairing N45 with the right finish

For indoor, dry duty a Ni-Cu-Ni finish is standard; for humidity or chemical exposure move to epoxy or a zinc system, and always check that the coating's own temperature limit clears the service temperature. The finish is part of the reliability, not an afterthought.

N45 in the catalogue context

N45 sits among the standard grades N42 through N58, a band chosen so that most ambient-temperature designs can find a match without jumping to the temperature-rated tiers. Within that band, N45 is the modest upgrade over N42; it is not a specialty grade, which is precisely why it is easy to source, quote and substitute. Treat it as the "a bit better than baseline" rung and you will use it well.

Frequently asked questions

Is N45 much stronger than N42? In energy product terms it is about seven percent higher (42-47 versus 39-44 MGOe), which is often enough to shrink a part or raise pull force without changing the design approach.

Does the coercivity change between N42 and N45? No. Both share the same intrinsic coercivity floor of 955 kA/m, so demagnetisation resistance is effectively the same.

What temperature can N45 withstand? The standard N grade is rated to a maximum operating temperature of 80℃. For higher sustained temperatures, move to a temperature-rated series such as H, SH, UH, EH or AH.

Should I always pick the highest grade I can afford? Not necessarily. Overspecifying the grade adds cost and can tighten consistency demands without real benefit; match the grade to the actual working point instead.

Can N45 be magnetised in any direction? Yes, within the limits of the shape - axial, diametric, radial or multi-pole magnetisation can all be arranged, and the direction must match the assembly.

If you are weighing N45 against another grade for a specific envelope, Request a quote with your target force and space so the best trade-off can be confirmed.