Choosing a neodymium magnet grade is rarely about reaching the highest number on a datasheet. For a large share of real products, a balanced mid-range grade such as N42 delivers everything the application needs while keeping material cost, machining risk and demagnetisation margin in a comfortable place. This article explains what an N42 neodymium magnet is, the exact figures behind the label, how to read the specification table, and the design situations where N42 is the pragmatic choice.
What the "N42" label means
Sintered neodymium magnets belong to the NdFeB (neodymium-iron-boron) family. The letter "N" marks a standard material that is not graded for elevated temperature, and the number that follows is the minimum maximum energy product in mega-Gauss-Oersteds (MGOe). An N42 magnet is therefore specified to reach at least 42 MGOe, with the published band running from 39 to 44 MGOe. That single number is a useful shorthand, but the full specification is what decides whether the magnet will survive and perform inside your product. The grade label tells you nothing about shape, coating, tolerance or magnetisation direction, all of which matter as much as the grade itself.
N42 specification at a glance
The figures below come from the sintered NdFeB material table and reflect the published grade band for N42:
- Remanence (Br): 1.28-1.32 T (12.8-13.2 kGs)
- Intrinsic coercivity (Hcj): at least 12 kOe (955 kA/m)
- Magnetic coercivity (Hcb): at least 11.6 kOe (923 kA/m)
- Maximum energy product ((BH)max): 39-44 MGOe (310-350 kJ/m³)
- Maximum operating temperature: 80℃
Two values deserve a closer look. The coercivity figures describe how strongly the magnet resists demagnetisation. An Hcj of 955 kA/m is the baseline for the whole standard N series and is ample for most room-temperature and mildly warmed assemblies. The 80℃ operating ceiling is the practical limit for the unmodified N grade before irreversible flux loss becomes a design risk.
Reading the table: remanence, coercivity and energy product
Remanence is the field the magnet holds when removed from the magnetising field; a higher Br means a stronger residual field for a given volume. Coercivity is the reverse field needed to reduce the magnetisation to zero, and it is the magnet's resistance to being demagnetised by heat, shock or opposing fields. The maximum energy product is the peak of the demagnetisation curve and the number most often quoted as "the grade". For N42, the band of 39-44 MGOe means a conforming part will sit somewhere in that window, and a buyer should expect the supplier to confirm which side of the band a given lot falls on for critical designs.
How N42 sits among the NdFeB grades
The standard series in the published table spans from the lower forties up to N58. N42 sits in the middle: below it sit slightly cheaper, slightly weaker grades, and above it sit stronger grades such as N45, N48, N50 and the top of the line at N52-N58. Moving up the scale gains energy product but also raises cost and, at the very top, can tighten tolerance and consistency demands. N42 is often the point where the price-performance curve is kindest for general industrial use, which is why it is one of the most widely stocked and quoted grades.
Where N42 makes the most sense
Because it pairs a healthy energy product with a manageable price and robust coercivity, N42 is a common choice for:
- Consumer and appliance holding magnets where size is not the dominant constraint
- Mid-size motors, actuators and magnetic couplings that run near ambient temperature
- Separation, lifting and fixturing tools where field strength matters more than miniaturisation
- Sensor and switch assemblies that need a stable bias field without exotic grade cost
- Educational, craft and promotional items where consistency matters more than peak force
When the design is space-limited and must pull hard from a tiny volume, a higher grade such as N48 or N50 may be worth the premium. When the part is large and cost-driven, a lower grade can be sufficient. N42 is the dependable default for "strong, cheap enough, and good enough for 80℃".
Magnetisation direction and tolerances
N42 is produced in discs, rings, blocks, arcs and custom geometries, each with a defined magnetisation direction - axial, diametric, radial or multi-pole. Tolerances are typically held to about ±1 percent, with tighter ±0.05 mm achievable on request for critical fits. Specifying the magnetisation direction correctly is as important as the grade, because a magnet magnetised the wrong way will not couple to the surrounding steel or coil regardless of how strong it is.
Stability, coating and handling notes
Like every sintered NdFeB part, an N42 magnet is hard and brittle and should be handled so it cannot snap against steel or another magnet. It is also prone to corrosion if left bare, so a protective finish is normal. Common finishes include nickel-copper-nickel (Ni-Cu-Ni), zinc and epoxy, selected by the operating environment. For room-temperature indoor use, Ni-Cu-Ni is the default; for humid or mildly corrosive settings, epoxy or thicker zinc systems are worth considering. The maximum operating temperature of 80℃ applies to the magnet itself; the plating system may have its own temperature limit that you should respect in parallel.
Working with a supplier on N42
When you request N42, the useful detail is not just the grade but the working point, shape tolerance, magnetisation direction and coating. YUECI KEJI supplies N42 in a full range of shapes with a quality system aligned with IATF16949 and ISO 9001/14001/45001, and can advise on the magnetic circuit so the chosen grade is matched to the real load rather than overspecified. For background on the family, see the NdFeB magnet overview.
Common mistakes when specifying N42
Three errors appear repeatedly. The first is treating the grade as the working point: the 39-44 MGOe band is the peak of the curve, not the flux your circuit actually sees, so always design from the demagnetisation curve at your load line. The second is forgetting the coating; an N42 left bare will corrode in humid air regardless of how good the magnetic numbers are. The third is getting the magnetisation direction wrong, which silently zeroes the coupling to the surrounding steel or coil. None of these is a grade problem, yet each can sink a project.
N42 and the temperature-rated series
When a design edges above 80℃, do not try to stretch N42 - step to the temperature-rated family instead. The M, H, SH, UH, EH and AH series cover 100℃ through 230℃ and are discussed in the high-temperature guide; for a standard, ambient-duty part, N42 stays the simpler, cheaper answer.
Frequently asked questions
The questions below are the ones engineers most often raise about this grade.
Is an N42 magnet strong enough for a small motor? For many miniature and mid-size motors it is, because the energy product of 39-44 MGOe is ample at the air gaps and temperatures those designs see. Very high-speed or high-temperature machines may need a higher grade or a temperature-rated series.
Does N42 need a coating? Yes. Sintered NdFeB corrodes if exposed, so a finish such as Ni-Cu-Ni, zinc or epoxy is standard even for indoor parts, and essential anywhere humid.
Can N42 be used above 80℃? Only with caution. The published maximum operating temperature for the standard N grade is 80℃. For sustained higher temperatures, a temperature-rated series such as H, SH, UH, EH or AH should be specified instead.
How does N42 differ from N45 or N48? N45 and N48 offer higher energy product (42-47 and 45-50 MGOe respectively) in exchange for a small cost increase, which helps when you must shrink the magnet or raise pull force in the same volume.
What tolerance can I expect on an N42 part? Standard dimensional tolerance is about ±1 percent, with tighter ±0.05 mm available on request for precision assemblies.
If your design needs a balanced, well-understood NdFeB grade, Request a quote and share your drawing or working point so the right geometry and finish can be proposed.