NdFeB

N45 Block Magnet

N45 block magnets pair mid-range NdFeB energy with the most machinable shape in the range. YUECI KEJI presses and grinds N45 blocks to your length, width and height, magnetized axially or radially.

N45 Block Axial / Radial / Multipole Custom size Coated to spec
N45 Block Magnet - YUECI KEJI

Specifications

GradeN45
ShapeBlock
CoatingNi-Cu-Ni, Zn, Epoxy, Au (custom on request)
ToleranceDimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
MagnetizationAxial / Radial / Multipole
ApplicationsIndustrial holding and lifting fixtures, motors, generators and magnetic separators, custom machined parts and assemblies
Lead timeProduction lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method.
MOQQuoted per inquiry
Export controlExport classification is confirmed per shipment against the product composition and destination.

What is an N45 block magnet

N45 block magnets are rectangular sintered NdFeB parts with two large flat pole faces. The block is the most machinable shape in the range and the cheapest route to a specific pole area, which is why it dominates holding, separation and custom assembly work. The N45 grade adds useful remanence over N42 without the cost of the top grades.

N45 magnetic performance

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Why choose N45

N45 lifts remanence and energy product clear of N42 without stepping into the process penalties of the high-fifties grades. It is the usual choice when a design was prototyped on N42 and the customer wants roughly 8% more flux in the same envelope.

Shape, dimensional tolerance and magnetization

Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.

Surface treatment

Test conditions and reports are available on request.

Coating choice follows the environment: bright Ni-Cu-Ni for indoor and clean-room work, zinc for cost-sensitive volume, and epoxy where the part is handled, exposed to salt mist or must not glare. Bare NdFeB corrodes quickly, so every block leaves the plant coated unless the brief explicitly calls for a phosphated or as-ground finish.

Typical applications

N45 blocks end up in holding fixtures and lifting tools, motor and separator pole pieces, and custom machined sub-assemblies where a flat pole face has to meet a flat steel pole piece.

Handling, storage and shipping

Sintered NdFeB is hard but brittle: it chips on impact and pinches fiercely when it snaps to steel. Parts ship in padded, magnetically shielded or spaced packing with keepers where the design calls for them, and air freight follows IATA packing instruction 902 with the field at the package surface measured before dispatch.

Custom sizing, prototyping and order minimums

Every dimension, grade suffix, coating and magnetization direction is built to your drawing or reproduced from your sample. Samples and small batches come first, then volume; repeat orders are faster because the tooling and the inspection routine already exist. Minimum order quantities are quoted per inquiry against the geometry and the grade.

Grade, temperature and coating — how this part is specified

A complete specification names the grade (including the temperature suffix), the shape and dimensions with tolerances, the magnetization direction, the coating and the destination. With those five points YUECI KEJI quotes quickly; with any of them missing the project waits. Working temperature is set by the suffix, not by the shape, and the coating is set by the environment.

Designing the magnetic circuit and working on the line

A block is the easiest shape to re-cut. If the force target is missed, adding height in the magnetization direction is usually cheaper than changing grade, and the extra material is available at N45 pricing. If the envelope is fixed, N48 or N50 recovers flux in the same envelope.

When to choose a different shape

A block is the default for flat pole work. Move to a disc or ring when the part must be round, to an arc or segment when the pole must curve around a rotor, and to a cube when equal edges simplify the fixture.

Where this material is typically used

Sintered NdFeB blocks in this grade end up in industrial holding and separation equipment, motors and generators, and custom machined assemblies — the workhorse jobs of the magnet industry.

Why buyers choose it

  • N45 gives strong remanence at a mid-range cost per kilogram in the most machinable shape.
  • Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
  • Axial, radial or multipole magnetization cut to drawing for motor and separator duty.
  • Coatings from bright Ni-Cu-Ni to non-reflective black epoxy for optical and medical builds.

Applications

Industrial holding and lifting fixtures

Motors, generators and magnetic separators

Custom machined parts and assemblies

Buyer Questions

N45 Block Magnet FAQs

Why choose a block over a disc?

A block gives the largest flat pole area per unit of material and is the easiest shape to grind, drill and array. Discs win when the part must be round.

Can N45 blocks be magnetized multipole?

Yes. Multipole magnetisation is routine for motor and separator duty; send the pole count and pitch and the magnetising fixture is built to match.

Are N45 blocks export Export documentation and licensing requirements are confirmed per shipment.?

Export classification is confirmed per shipment against the product composition and destination.

Request a quote for N45