Ferrite

Ferrite Segment Magnet

Ferrite segment magnets are curved ceramic pieces that nest into motor pole rings. YUECI KEJI presses and magnetizes ferrite segments to drawing with no plating needed.

Ferrite Segment / arc Radial / axial Matched sets No plating needed
Ferrite Segment Magnet - YUECI KEJI

Applications

Volume motor rotors

Magnetic separators and grills

Couplings and clutches

Why buyers choose it

  • Ferrite is the lowest-cost permanent magnet family per unit.
  • Intrinsic corrosion resistance — no plating needed for outdoor or wet duty.
  • Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
  • Operating temperature well above the standard NdFeB range.

Specifications

MaterialHard ferrite (ceramic)
ShapeSegment / arc
CoatingAs-pressed / painted / epoxy on request
ToleranceDimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
MagnetizationRadial / Tangential / Multipole
ApplicationsMotor rotors, Separators, Couplings
Lead timeProduction lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method.
MOQQuoted per inquiry
Export controlExport classification is confirmed per shipment against the product composition and destination.

What a ferrite segment actually is

A ferrite segment is a curved ceramic wedge, not a slab: its two end faces meet at the ring angle, and a full pole ring is built by placing many segments shoulder to shoulder. Because the pole count is set by how many wedges you fit, a multipole rotor can be assembled without a bespoke magnetising fixture.

At YUECI KEJI segments are pressed, sintered and ground to your inner radius, outer radius, chord angle and thickness, then magnetised to drawing. Matched sets are pressed and inspected together so the pole pattern closes around the bore. No plating is needed on the ceramic body.

Why segment geometry drives the build

Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.

Material behaviour you design around

Hard ferrite is a strontium or barium ceramic — the lowest-cost permanent-magnet family, corrosion-resistant with no plating, and happy well above the NdFeB temperature ceiling. It is brittle, so a segment chips if dropped or clamped on a sharp edge; it belongs in assemblies where impact is unlikely. Against NdFeB the trade is explicit: roughly a quarter of the energy per unit volume, at a fraction of the cost and with far better heat and weather behaviour.

Segment-specific applications

Segments are the volume workhorse of curved ferrite pole rings: BLDC and PMSM rotor rings, stepper and brushless blower rotors, magnetic separator grills, and coupling rings where the torque target is modest and the piece price is the constraint. When the pole count is odd or the annulus is thin, segments beat a full ring on material use.

Handling, stacking and shipping segments

Because the ceramic is brittle, segments ship in padded, separated packing with the curved faces protected. There is no plating to corrode, so dry storage is enough; matched sets are kept together and labelled by ring.

Custom radii, angles and order minimums

Every inner radius, outer radius, chord angle, thickness and magnetisation direction is built to your drawing or reproduced from a sample. Repeat orders are faster because the tooling exists. Prototype quantities are supported.

Specifying a segment order

A complete specification names the material grade, the two radii, the chord angle, the thickness, the magnetisation direction and the quantity. Ferrite grades are chosen for coercivity and temperature rather than a numbered energy band; the exact grade window is confirmed on request.

Designing the rotor circuit

A segment rotor is designed around volume, not grade: because the energy per unit volume is roughly a quarter of NdFeB, the cheapest fix for a missed torque target is usually a thicker segment, more poles, or a larger bore — not a material change. Keep the radial wall thick enough to survive press-fit and centripetal load.

When a segment is the wrong shape

A segment is the default for curved ferrite pole work with an odd or fine pole count. Move to a full ring when the annulus is continuous, to a block when the pole face is flat, and to NdFeB when force density beats price.

Where segments are typically used

They end up in volume motor rotors, separator grills and couplings — the high-volume, cost-first rotary work where ferrite's price and weather resistance decide the bill of materials.

Buyer Questions

Ferrite Segment Magnet FAQs

Can matched segment sets be supplied?

Yes. Segments for one rotor are pressed, ground, magnetized and inspected as a set so the pole pattern closes correctly around the ring.

Why choose segments instead of a full ring?

Segments waste less material on odd pole counts and are easier to magnetize multipole. A full ring wins when the annulus is continuous and the pole count is even.

Are ferrite segments export Export documentation and licensing requirements are confirmed per shipment.?

Export classification is confirmed per shipment against the product composition and destination.

Request a quote for Ferrite Segment Magnet