The N50 neodymium magnet is the strongest of the standard, unmodified NdFeB grades before the line steps up to N52, N54, N55, N56 and N58. With a 47-52 MGOe energy product it delivers close to the maximum field the standard 80℃ route can offer, which makes it the natural choice when an application needs the highest practical room-temperature performance without moving to the most specialised top grades. This article sets out the N50 specification and where it fits.
N50 specification
The published sintered NdFeB band for N50 is:
- Remanence (Br): 1.39-1.44 T (13.9-14.4 kGs)
- Intrinsic coercivity (Hcj): at least 12 kOe (955 kA/m)
- Magnetic coercivity (Hcb): at least 11.0 kOe (876 kA/m)
- Maximum energy product ((BH)max): 47-52 MGOe (374-414 kJ/m³)
- Maximum operating temperature: 80℃
The coercivity floor of 955 kA/m is unchanged from the rest of the standard N series. The headline gain is remanence (up to 1.44 T) and energy product (up to 52 MGOe), so N50 packs the most flux per volume that this production route reliably delivers.
Reading the N50 numbers
As with every grade, the quoted energy product is the peak of the demagnetisation curve, not the field at your working point. For a tightly designed part the magnet will sit somewhere down that curve, so the practical benefit of N50 is headroom: it lets a compact design hit its force target with margin, or hit a higher target in the same envelope. The remanence of 1.39-1.44 T also helps where the air gap is large and flux must be maintained across it.
Why choose N50
N50 is the answer when volume is severely constrained and the design must extract the last bit of standard-grade performance. Typical uses include:
- Ultra-compact motors and generators where every gram and cubic millimetre counts
- High-field magnetic couplings and clutches in a tight bore
- Precision actuators, medical and laboratory instruments
- Miniature holding and indexing magnets that must stay small yet strong
- High-density sensor and encoder poles
Against N48, N50 adds a further few MGOe; against the very top grades N52-N58, it stays on the simpler standard route and is usually easier to source and process in volume.
N50 versus the top of the line
Grades N52 through N58 push the energy product toward 49-60 MGOe, but they sit at the extreme of the standard series where consistency and cost move against you. N50 is the sweet spot for "as strong as practical on the standard route". If the design genuinely needs more than 52 MGOe, the top grades are the only option; if it does not, N50 avoids paying for headroom it cannot use.
Coating and handling
Sintered NdFeB is hard, brittle and corrosion-sensitive, and N50 parts are often small and highly loaded, so finish quality is critical. Nickel-copper-nickel is the standard indoor plating; epoxy or zinc systems suit humidity, salt spray or chemical duty. Keep both the 80℃ magnet limit and the coating temperature rating in view when the part sees heat, and specify magnetisation direction and tolerance up front.
Working with a supplier
Specifying N50 well means giving the supplier the working point and the shape as well as the grade, so the delivered part meets the load line rather than just the band. YUECI KEJI supplies N50 across standard and custom geometries and can model the circuit so the grade is matched to the real load. For the wider family, see the NdFeB magnet overview.
Pushing to the edge of the standard route
N50 is about as far as the standard, unmodified NdFeB route comfortably goes before the top grades take over. That makes it the right call when you need the last few MGOe of standard-grade performance, but it also means there is little headroom left for process variation, so lot-to-lot consistency and supplier control matter more than at N42. Confirm the supplier's process capability for the geometry you need.
When to step up to N52-N58
If the calculation shows you need more than 52 MGOe, the top grades N52 through N58 are the only option, accepting higher cost and tighter control. If it does not, staying at N50 keeps you on the simpler, more economical standard route. The deciding line is the actual energy product your working point demands, not a preference for a bigger number.
Why N50 is a system decision
Choosing N50 usually means the product is already volume-constrained, so the rest of the assembly - pole pieces, air gap, retention - is also tight. The grade is the last lever, not the first; confirm the circuit and the gap before committing to the near-top standard grade, because the premium is only worth paying when the volume truly cannot grow.
Heat, coating and N50
N50 shares the 80℃ ceiling of the standard route, so any heat above that demands a temperature-rated series instead. The coating must also suit the environment and clear the service temperature; Ni-Cu-Ni or epoxy are the usual choices, selected by humidity and chemical exposure rather than by appearance.
Ordering N50 well
State the working point, the shape and the magnetisation pattern, and request the demagnetisation curve for the lot. That turns "N50" from a hope into a verified component and prevents the silent field losses that come from assuming the grade alone defines performance.
A note on grade headroom
Designing at N50 leaves little margin below the top of the standard route, so it suits products that are settled rather than prototypes still moving. If the design is likely to shift, a slightly lower grade buys tolerance for change; if it is frozen, N50 delivers maximum standard-route performance with minimum wasted headroom, which is exactly what a mature, volume product wants.
N50 and the standard-range ceiling
Once a design settles on N50, the next step up is the top of the standard range, N52 through N58, and beyond that the temperature-rated tiers. Knowing where N50 sits helps you recognise when a requirement has outgrown the standard route and a different branch is needed, rather than pushing a grade past its sensible limit.
Frequently asked questions
What is the strongest standard NdFeB grade? The published standard series tops out at N58, but N50 is the strongest of the broadly economical standard grades before the extreme top; N52-N58 push further at higher cost and tighter control.
Can N50 run hot? The standard N grade is rated to 80℃ maximum operating temperature. For sustained heat, specify a temperature-rated series such as H, SH, UH, EH or AH.
Is N50 more brittle than lower grades? All sintered NdFeB is similarly hard and brittle regardless of grade; handling and mounting methods matter more than the grade number.
How do I choose between N48 and N50? If the design needs the last few MGOe of standard-grade performance in a tiny envelope, pick N50; otherwise N48 is the more economical high-energy choice.
Does N50 need a special coating? No special coating is required beyond the usual NdFeB protection; choose Ni-Cu-Ni, zinc or epoxy by environment, matching the coating temperature limit to service.
To confirm whether N50 is the right ceiling for your design, Request a quote with your force and space targets so the grade and geometry can be matched.