TECHNOLOGY

Magnet Surface Treatment: Coatings Across NdFeB, Ferrite, SmCo and Alnico | YUECI KEJI

Most magnet failures in the field are not magnetic - they are corrosion and wear. Magnet surface treatment is the discipline of protecting the part and, sometimes, the assembly around it.

Most magnet failures in the field are not magnetic - they are corrosion and wear. Magnet surface treatment is the discipline of protecting the part and, sometimes, the assembly around it. This article takes the wider view across materials: it presents the coating options and their test data, then explains why sintered NdFeB, ferrite, samarium cobalt and alnico each call for a different treatment philosophy. A companion article covers NdFeB coating choices in finer detail; this one is the cross-material overview.

Why surface treatment matters

Neodymium-iron-boron is the strongest permanent magnet family but also the most chemically active; left bare it rusts quickly in humid air. Ferrite, by contrast, is a ceramic that is largely indifferent to corrosion. Samarium cobalt and alnico sit between. The right finish therefore depends less on the shape than on the base material and the environment the magnet will see.

The coating options and their test data

The table below lists the standard finishes offered, with their colour, thickness, salt-spray and pressure-cooker (PCT) performance and working-temperature limit:

  • Phosphating - gray, <3 µm, no salt-spray or PCT rating, used as a base or for mild duty
  • Plastic (RB) - blue, 0.5-3 µm, thin decorative or insulating layer
  • White zinc - white, 5-10 µm, salt spray >24 hr, working temperature <160℃
  • Colorized zinc - multicolour, 5-10 µm, salt spray >48 hr, working temperature <160℃
  • Ni-Cu-Ni - silver, 12-25 µm, PCT >48 hr, salt spray >72 hr, working temperature <200℃
  • Cu-Ni - silver, 12-20 µm, PCT >48 hr, salt spray >72 hr, working temperature <200℃
  • Zn-Ni - blue, 5-15 µm, PCT >24 hr, salt spray >240 hr, working temperature <200℃
  • Electrophoresis epoxy - white to silver, 15-30 µm, PCT >96 hr, salt spray >500 hr, working temperature <160℃
  • Spraying epoxy - black, 15-30 µm, PCT >240 hr, salt spray >500 hr, working temperature <200℃
  • Ni-Cu + epoxy - black, 25-45 µm, PCT >150 hr, salt spray >800 hr, working temperature <200℃

The numbers tell a clear story. Bare or thin metallic coatings buy appearance and light protection; nickel-copper-nickel is the general-purpose workhorse; and the epoxy systems - especially Ni-Cu plus epoxy - dominate where salt spray and humidity are severe, with the black Ni-Cu+epoxy combination surviving beyond 800 hours of salt spray.

Treatment by material

NdFeB. Almost always coated. Ni-Cu-Ni is the default for indoor and general use; epoxy or Zn-Ni systems are specified for marine, outdoor or chemical service. The coating's own temperature limit must clear the service temperature, so a 200℃ epoxy or Ni-Cu-Ni is paired with high-temperature grades while a 160℃ finish is not.

Ferrite. As a ceramic, sintered ferrite is inherently corrosion resistant and is frequently supplied bare. Where appearance, insulation or a coloured finish is wanted, paint or a plastic coat is applied, but there is no corrosion-driven need for plating.

Samarium cobalt. SmCo resists corrosion well and is often used bare, though a thin coating may be added for electrical insulation, colour coding or a cleaner surface in food- and medical-adjacent settings.

Alnico. Alnico is reasonably stable but can discolour and, in some environments, oxidise at edges; it is commonly painted, plated or left machined depending on the duty. Its lower coercivity also means careful handling to avoid demagnetisation during finishing.

Rubber and flexible magnets. Here the "treatment" is the binder itself: ferrite powder held in rubber or PVC is sealed by the matrix, so the part needs no separate plating and is naturally resistant to moisture at the surface.

Choosing the finish: a decision path

Start from the environment, not the catalogue. Indoor, dry, benign duty leads to Ni-Cu-Ni or even phosphating. Humid or outdoor leads to epoxy or Zn-Ni. Salt spray, wash-down or marine leads to Ni-Cu+epoxy. Then check that the coating's working-temperature limit clears the magnet's service temperature, confirm the finish is compatible with any bonding or potting step, and verify the coating thickness is adequate at edges where corrosion starts. A finish chosen this way protects the magnet for its service life rather than just looking right on arrival.

Appearance versus protection

A bright nickel finish looks finished, but appearance is not protection. The salt-spray and PCT numbers are what predict field life, and a thin or porous decorative coat can fail long before a plainer-looking robust one. Specify the finish by the environment it must survive, and treat colour or shine as secondary.

Life-cycle and rework

Coatings can be damaged during press-fit assembly or by repeated disassembly, and once the substrate shows through, corrosion starts at that spot. For parts that will be handled or reworked, favour thicker, more forgiving systems such as epoxy, and brief assemblers on presenting the magnet so edges are not chipped against steel.

Coating selection by environment

A simple way to choose: dry indoor duty takes Ni-Cu-Ni or phosphating; humid or outdoor duty takes epoxy or Zn-Ni; marine, wash-down or chemical duty takes Ni-Cu+epoxy, which exceeded 800 hours of salt spray in testing. Match the finish to the worst condition the part will actually see, not the average.

Thickness, edges and reality

Corrosion almost always starts at an exposed edge, so the effective protection is the coating thickness and continuity at the edge, not the nominal thickness on a flat face. For parts with cut edges or tight corners, specify a system with good edge coverage, such as an epoxy, and verify it after any secondary operation that could nick the finish.

Cost of the finish

Coatings add both material and process cost, and the most protective systems (epoxy, Ni-Cu+epoxy) cost more than a simple Ni-Cu-Ni. The right economic answer is to pay for the protection the environment actually requires and no more; over-specifying the finish wastes money, under-specifying it risks the whole assembly, so the environment-driven choice is usually the cheapest correct one.

When in doubt, ask

If the environment is mixed or unclear, describe it to the supplier rather than guessing a finish. A short conversation about humidity, chemicals, temperature and whether the part will be handled usually settles the choice between a simple Ni-Cu-Ni and a full Ni-Cu+epoxy system, and prevents both over- and under-specification.

Frequently asked questions

Do all magnets need plating? No. Ferrite and rubber magnets are often left untreated or merely painted, while NdFeB almost always needs a protective finish.

Which coating resists salt spray best? The black Ni-Cu + epoxy combination exceeds 800 hours of salt spray in testing, making it the choice for marine and wash-down duty.

Does the coating limit working temperature? Yes. Each finish has its own limit - some epoxy and zinc systems stop at 160℃, while Ni-Cu-Ni and several epoxies reach 200℃.

Can I coat a magnet after it is magnetised? Usually yes, but the process and any heat must be kept below the grade's limits; for high-coercivity grades this is straightforward, for standard grades care is needed.

Why does edge coverage matter most? Corrosion almost always begins at an exposed edge where the substrate shows through, so coating thickness and continuity at edges decide real-world life more than the nominal thickness elsewhere.

To specify the right finish for your material and environment, Request a quote with the duty cycle and any bonding requirements so the coating can be matched.