You cannot improve what you cannot measure, and magnetic field is no exception. This guide to how to measure magnetic field strength covers the units, the instrument and the technique that gives a number you can actually trust.
The short answer: gauss meter plus Hall probe
A gauss meter (sometimes called a tesla meter) with a Hall-effect probe is the standard tool. You place the probe at the point of interest, usually on or just above the magnet's surface, and the meter reads the flux density. The reading is in gauss or tesla, and converting between them is just moving the decimal: one tesla equals ten thousand gauss.
For production and incoming inspection we use calibrated magnetic measuring instruments so every magnet is checked against its specification.
Gauss versus tesla
Both units describe magnetic flux density; they differ only in scale.
- Tesla (T): the SI unit; everyday magnets are fractions of a tesla.
- Gauss (G): the cgs unit; one tesla equals 10,000 gauss.
- Conversion: multiply tesla by 10,000 to get gauss, divide gauss by 10,000 for tesla.
Most magnet datasheets and handheld meters use gauss because the numbers are convenient; a surface field of a few thousand gauss reads far more naturally than a fraction of a tesla.
How a Hall probe works
A Hall sensor outputs a voltage proportional to the perpendicular magnetic field passing through it. The meter converts that voltage to a flux-density reading. Because the sensor responds to the field component perpendicular to its face, probe orientation is not optional; it is part of the measurement.
- Perpendicular field: align the probe face to the field for a true reading.
- Flat surfaces: press the probe flat for a surface-field measurement.
- Gaps: hold the probe at the defined distance for a gap-field measurement.
Measuring a surface field
The surface field is the field at the magnet's face, and it is what most people mean by 'how strong is it'. To measure it:
- Zero or tare the meter in a field-free area.
- Place the Hall probe flat against the magnet face.
- Orient the probe so its active face is perpendicular to the field.
- Read the value in gauss (or tesla) and record it.
Expect the reading to vary with position; the peak is usually at the pole centre, falling toward the edges.
Measuring at a distance or in a gap
Many applications care about the field at a working gap, not the surface. Repeat the same steps but hold the probe at the specified distance or position. Because field falls off rapidly with distance, even a millimetre of error changes the number, so a fixture or spacer helps repeatability.
Common measurement mistakes
- Wrong orientation: a tilted probe under-reads because it sees only the perpendicular component.
- Inconsistent position: hand-held probes wander, giving different numbers each time.
- Uncalibrated meter: drift and offset make the reading meaningless.
- Nearby steel: ferromagnetic objects distort the local field; measure away from them.
What the reading tells you
A field measurement verifies the magnet matches its grade and magnetization. A low reading can reveal a wrong grade, a reversed or weak magnetization, damage, or a coating that changed the effective gap. In production, surface-field testing is a fast pass-fail check that catches bad parts before they ship.
Choosing a meter
Handheld gauss meter
Portable, simple, ideal for incoming inspection and field service. Resolution and range should suit your magnets; very strong NdFeB can exceed a low-range probe.
Axial and transverse probes
An axial probe measures field along its axis (good for flat faces); a transverse probe measures across its face (good for side fields and inside bores). Match the probe to where you measure.
Calibration
Use a meter with current calibration and, for critical work, verify against a reference magnet so your numbers are defensible.
Practical tips for repeatable results
- Always measure at the same point and orientation.
- Use a jig for gap measurements.
- Keep steel and other magnets away during the reading.
- Log results so trends over a batch are visible.
Calibration and measurement uncertainty
A reading is only as good as the instrument behind it. Hall probes drift with use and temperature, so a meter that was accurate last year may be off today. Periodic calibration against a reference, and a zero-check in a field-free spot before each session, keeps the numbers trustworthy. For incoming inspection where a pass-fail decision hinges on the reading, this discipline is what makes the check defensible.
Uncertainty also comes from placement: a hand-held probe that wanders by a millimetre over a strong gradient can swing the reading noticeably. A simple fixture or spacer that fixes the probe position turns a vague number into a repeatable one, which matters far more than extra decimal places on the display.
Field patterns you should expect
A disc magnet shows the highest reading at the pole-face centre, falling toward the edges and dropping fast with distance. A ring or rod shows a different profile depending on magnetization direction, which is why you measure at the point the application actually cares about rather than a convenient spot. Understanding the expected shape of the field helps you spot a mis-magnetized or damaged part: a flat or lopsided reading where a clean peak should be is itself a diagnostic.
Choosing a probe type
An axial probe senses field along its axis and suits flat faces; a transverse probe senses across its face and suits side fields and inside bores. Matching the probe to the geometry is half the battle, because the wrong probe simply cannot be oriented to the field. For shops that measure both, owning both probe styles avoids the temptation to 'make do' with the wrong one and misread the result.
Reporting the result
A field reading is only useful if it is tied to a position, orientation and date. Record those with the number so a later comparison is meaningful and a failed part can be traced. A logbook of readings, however simple, turns a gauss meter from a curiosity into a genuine quality instrument and gives every magnet a verifiable birth record.
Frequently asked questions
The measurement questions we hear from inspectors and engineers.
What is the difference between gauss and tesla? They measure the same flux density at different scales: one tesla equals 10,000 gauss. Most magnet work uses gauss because the numbers are convenient.
What instrument measures magnetic field? A gauss meter (or tesla meter) with a Hall-effect probe, which outputs a voltage proportional to the perpendicular magnetic field and converts it to a reading.
How do I measure a magnet's surface field? Tare the meter in a field-free area, press the Hall probe flat against the magnet face, orient it perpendicular to the field, and read the value, noting that the peak is usually at the pole centre.
Why does my reading change with position? Because field strength varies across and away from the magnet, and a tilted probe only sees the perpendicular component; consistent point, orientation and distance give consistent numbers.
Can field measurement verify a magnet grade? Yes. A surface or gap reading that matches the specification confirms grade and magnetization, while a low reading can reveal a wrong grade, weak magnetization or damage.
Need calibrated measuring tools or inspection support? Request a quote and our team will help you specify the right gauss meter and probe for your magnets.