PRACTICAL

How to Identify a Neodymium Magnet: 6 Field Tests | YUECI KEJI

Magnets get separated from their labels, salvaged from scrap and passed around workshops. These six tests will tell you what you are actually holding.

Workshops accumulate unlabelled magnets, and buyers occasionally need to verify that what arrived is what was ordered. You do not need a laboratory: six simple checks separate neodymium from the other three commercial families with reasonable confidence, and a couple of them separate NdFeB from SmCo as well.

1. Appearance

Sintered NdFeB is almost always plated, usually nickel-copper-nickel, which gives it a bright silvery, slightly bluish metallic finish. Edges and ground faces are smooth and precise. Ferrite is a dull dark grey, unplated, with a matte ceramic surface. SmCo is also often unplated or lightly passivated, with a darker, slightly bluish-grey metallic look. Alnico is the distinctive one: a bright, slightly reddish cast metal with visible casting texture, and its poles often look like separate metal buttons.

2. Weight for size

NdFeB is dense, around 7.5 grams per cubic centimetre. Ferrite is much lighter, around 5. SmCo is around 8.2, slightly heavier than NdFeB, and alnico around 7.3. Weighing a part and dividing by its calculated volume gives a density that immediately separates ferrite from the metallic families, and separates alnico from NdFeB with a careful calculation. A small digital scale and a tape measure are enough.

3. Does a magnet stick to it strongly?

This is the quickest single test. Bring a known magnet close: NdFeB attracts another magnet powerfully and will jump to it from a centimetre or more. Ferrite attracts a magnet only weakly, and from a much shorter distance. Alnico attracts weakly too. If a magnet can lift another magnet of the same size off the bench, it is almost certainly NdFeB.

4. Pull force against steel

Compare against a same-size reference. A grade-42 NdFeB disc of a given size pulls several times harder than a ferrite disc of the same size, because ferrite's energy product is roughly an order of magnitude lower. If you have a scale and a steel plate, a measured comparison settles the question in seconds. The pull force article covers the test method.

5. Does it stick to stainless steel?

Most austenitic stainless steels are weakly magnetic, and this test is about degree. An NdFeB magnet holds firmly to many 304 and 316 surfaces, where a ferrite magnet of the same size barely grips. It is not a clean test, because stainless varies, but combined with the others it adds confidence.

6. Machining marks and tolerance

NdFeB is ground after sintering, so its surfaces show fine parallel grinding marks and its dimensions are held tightly, typically about plus or minus one percent. Ferrite is pressed near net shape and shows coarser, less regular surfaces with looser dimensions. Cast alnico shows casting texture and often needs grinding to reach tolerance. Under a loupe, the difference in surface finish is obvious.

Separating NdFeB from SmCo

This is the hard pair, because both are metallic, dense and strongly magnetic. Three clues help. SmCo usually has no plating, or only a light passivation, where NdFeB is brightly plated. SmCo is slightly denser. And SmCo's remanence is lower, so a same-size SmCo part reads slightly weaker on a gaussmeter, typically 10 to 20 percent below an equivalent NdFeB grade. If the part came from a high-temperature application, suspect SmCo; if from a general-purpose one, NdFeB. For a definitive answer, ask the supplier for a material certificate or run an EDX check.

Frequently asked questions

Can I identify the grade from a pull test?Roughly, against a known reference, but grade determination really needs a hysteresisgraph measurement or a flux measurement against a calibrated standard.

Why is my NdFeB magnet slightly rusty at the edges?Because the plating has been breached, usually by a chip or by corrosion that started at a defect. NdFeB corrodes rapidly once the plating is broken, which is one reason coatings are specified carefully.

Is a magnet that sticks to a refrigerator definitely NdFeB?No. Fridge-door magnets are usually flexible ferrite or a printed ferrite sheet. But a magnet that sticks strongly to the side of a steel cabinet is probably NdFeB.

How do I verify what a supplier sent?Ask for the flux measurement and the material grade on the inspection report. Both are recorded per lot against your part number.

Need a magnet identified or verified against an order? Send us photographs and dimensions and we will tell you what you have.