PRACTICAL

How to Demagnetize a Magnet (Safely, and When You Should) | YUECI KEJI

Demagnetizing is occasionally necessary, occasionally useful, and occasionally attempted with methods that do not work. Here is what actually demagnetizes a magnet.

Deliberately demagnetizing a magnet is a rare need. It comes up in scrap processing, in tooling that has to be cleaned of magnetic debris, and occasionally when a magnetized part has to be shipped or handled safely. The methods that work are fewer than the folklore suggests, and one of the most common suggestions does nothing at all to the magnets most people own.

Heat: the reliable method

Heating a magnet above its Curie temperature destroys its magnetization. For NdFeB that is somewhere between 310 and 380 degrees Celsius depending on the grade; for ferrite and SmCo the figure is considerably higher. Cooling the part afterwards does not restore the original magnet: the material can be re-magnetized, but it is a new part with new properties, and the structure has been through a phase transition. Heat is reliable, irreversible and best treated as a one-way operation.

Alternating field decay

The industrial method is to place the part inside a coil carrying an alternating current whose amplitude is slowly reduced to zero. Each cycle drives the magnetization back and forth with decreasing amplitude, and the material ends near zero remanence. This is how demagnetizing tools, chucks and heads work, and it leaves the material physically unchanged, which is why it is the preferred method when the part has to survive the process. The field required is several times the material's coercivity, so a demagnetizer sized for mild steel will not fully demagnetize a high-coercivity NdFeB part.

Hammering and impact: mostly a myth for modern magnets

The old advice to hit a magnet with a hammer has a real basis, but only for low-coercivity materials such as alnico, where mechanical shock can disrupt the domain structure. Sintered NdFeB and ferrite are hard and brittle; hammering them chips them long before it demagnetizes them. If you have tried this on a neodymium magnet and concluded it did not work, you were right.

When demagnetizing is actually useful

  • Scrap and recycling: mixed ferrous scrap is easier to handle and separate when the magnets in it are dead, and high-coercivity NdFeB scrap is specifically demagnetized before processing.
  • Tooling: magnetic chucks, lifters and fixtures are demagnetized when parts have to be released cleanly.
  • Shipping and handling: a dead magnet is easier and safer to pack, though the weight is unchanged.
  • Assembly work: temporarily killing a field so a part can be positioned without it jumping.

When it is the wrong answer

If the goal is to reduce a magnet's field in an assembly, shielding or a keeper is almost always better than demagnetizing, because the magnet keeps its strength for when you want it. If the goal is to dispose of a magnet safely, heat is unnecessary; a magnet in normal waste is inert. And if the goal is to weaken a magnet for a child's toy, do not: use a properly rated weak magnet instead, because a partially demagnetized magnet is unpredictable.

Safety notes

Heating NdFeB to Curie temperatures means handling hot, brittle parts that can crack from thermal shock, and the coating can smoke. AC demagnetizers draw serious current and get hot. For anything larger than a small part, use proper equipment and proper ventilation, and do not improvise with a stove and a coil.

Frequently asked questions

Will a magnet demagnetize itself over time?Modern sintered magnets are very stable. Slow self-demagnetization is a real phenomenon but negligible over a normal product lifetime unless the magnet is operating above its temperature class or against a strong opposing field.

Can a demagnetized magnet be re-magnetized?If it was demagnetized by an AC field and not overheated, yes, and it will come back close to its original strength. If it was heated past Curie, it can be re-magnetized but should be treated as a new part.

Does boiling a magnet demagnetize it?No. Boiling water is around 100 degrees, far below the Curie temperature of any commercial magnet material.

How do I demagnetize a large assembly?Usually you cannot, usefully. Either design the assembly with a keeper or shield, or specify the parts unmagnetized and magnetize after assembly.

Need parts supplied unmagnetized, or help with a scrap-processing requirement? Tell us the situation and we will suggest the practical route.