PROCESS

How Are Magnets Magnetized? Pulse Magnetizing Explained | YUECI KEJI

Magnetizing is the last step of making a magnet and the one that decides whether the part works at all. Here is how it is done and why the timing matters so much.

A sintered magnet is not magnetic when it leaves the grinding line. It becomes a magnet in a final step called magnetizing, where a strong field is applied through a fixture that determines the pole pattern. Everything about the part's behavior, which way it pulls, how many poles it has, and how uniformly it does so, is decided in this step rather than in the press.

Why magnetizing comes last

An unmagnetized magnet is much easier to handle. It does not attract swarf, it does not jump toward steel fixtures, and two parts will not slam together and chip. Pressing, sintering, grinding and coating are all done on unmagnetized stock, and only the finished, inspected part is magnetized, usually just before packing. This is also why a supplier can quote tight tolerances: the machining happens before the part has any field to distort gauges or attract debris.

Pulse magnetizing

The standard industrial method charges a bank of capacitors and discharges it through a coil wrapped around a fixture holding the part. The pulse lasts microseconds and reaches fields several times the magnet's intrinsic coercivity, which is what is needed to drive the material fully into saturation on the desired axis. The fixture, not the coil, defines the pattern: a simple two-pole fixture magnetizes through one axis, while a multipole fixture with segmented pole pieces writes an alternating pattern around a ring.

Constant-field magnetizing

An older method uses a DC electromagnet, either a solenoid or an iron-core coil, to apply a steady field while the part is held in the fixture. It works and is still used for large parts and for laboratory work, but it needs continuous cooling and much more installed power than a pulse system of equivalent peak field. Most production magnetizing today is pulsed.

Why the fixture is a real cost

A multipole fixture is a precision tool. Its pole pieces are positioned to fractions of a degree and fractions of a millimetre, and the same fixture is used for every part in a production run. This is why a multipole part costs more than a simple axially magnetized disc of the same grade and size, and why changing the pole count mid-project means a new fixture and a new approval cycle. It is also why multipole patterns are quoted per design rather than per part number.

Why a finished assembly usually cannot be re-poled

Once a magnet is bonded into an assembly, the steel around it distorts the field and the magnet is no longer in a known position relative to a clean fixture. Pulsing an assembly magnetizes everything in the field, including magnets you wanted left alone, and the result is unpredictable. Hybrid stepper rotors are the classic example: the rotor is assembled from two pole pieces and a magnet that was magnetized as a bare part, because a finished rotor cannot be pulsed to pattern without demagnetizing the wrong poles.

How magnetizing quality is verified

Three checks cover most of it. Total flux, measured with a coil and fluxmeter, confirms the part is magnetized to strength. Surface field mapping, with a Hall probe stepped around the pole face, confirms the pattern is where it should be. Dimensional inspection confirms the fixture held the part correctly. On multipole parts the pattern check is the one that catches fixture wear, and it is the reason multipole parts carry a per-lot measurement record.

Frequently asked questions

Can you supply magnets unmagnetized?Yes, for customers who need to machine or assemble first and magnetize later. Stock blanks in the block blank range are supplied unmagnetized for exactly this reason.

Can a magnet be demagnetized and re-magnetized?A correctly magnetized part that is later demagnetized by heat or an opposing field can sometimes be re-magnetized if it was not taken past the knee, but the result must be re-verified. Treat re-magnetizing as a repair, not a process step.

Does magnetizing change the dimensions?Negligibly for sintered NdFeB, which is why it is done last. The magnetostrictive forces are small enough to ignore at the tolerances we work to.

How many poles can you write on a ring?Common multipole patterns run from a handful of poles to dozens, set by the fixture. Send the pole count and the pattern drawing and we will confirm the fixture.

Need a specific pole pattern or multipole fixture? Send the pattern drawing and we will quote the fixture and the parts together.