NdFeB

N52H Disc Magnet

N52H disc magnets hold near-top-grade flux in duty that runs to 120℃. YUECI KEJI presses and grinds N52H discs to your diameter and thickness with axial, diametric or radial magnetization.

N52H Disc Axial / Diametric / Radial Export licence managed
N52H Disc Magnet - YUECI KEJI

Specifications

GradeN52H
ShapeDisc
CoatingNi-Cu-Ni, Zn, Epoxy, Au (custom on request)
ToleranceDimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
MagnetizationAxial / Diametric / Radial
ApplicationsAutomotive sensors and actuators, under-bonnet and hot-zone fixtures, thermal-cycled holding assemblies
Lead timeProduction lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method.
MOQQuoted per inquiry
Export controlExport classification is confirmed per shipment against the product composition and destination.

What is an N52H disc magnet

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

N52H magnetic performance

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Why choose N52H for hot duty

The H series trades a little energy product for coercivity: the heavy rare-earth addition keeps the grade magnetically stable to 120℃, which is the band where standard N52 starts to lose reversible flux. Choose H when the part runs warm but the force budget is still generous.

Shape, dimensional tolerance and magnetization

Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.

Surface treatment

Test conditions and reports are available on request.

Coating choice follows the environment: bright Ni-Cu-Ni for indoor and clean-room work, zinc for cost-sensitive volume, and epoxy where the part is handled, exposed to salt mist or must not glare. Bare NdFeB corrodes quickly, so every disc leaves the plant coated unless the brief explicitly calls for a phosphated or as-ground finish.

Typical applications

N52H discs end up in warm duty: automotive sensors and actuators, under-bonnet fixtures, hot-zone holding assemblies and anything that thermal-cycles between a cold start and a hot soak.

Handling, storage and shipping

Sintered NdFeB is hard but brittle: it chips on impact and pinches fiercely when it snaps to steel. Parts ship in padded, magnetically shielded or spaced packing with keepers where the design calls for them, and air freight follows IATA packing instruction 902 with the field at the package surface measured before dispatch.

Custom sizing, prototyping and order minimums

Every dimension, grade suffix, coating and magnetization direction is built to your drawing or reproduced from your sample. Samples and small batches come first, then volume; repeat orders are faster because the tooling and the inspection routine already exist. Minimum order quantities are quoted per inquiry against the geometry and the grade.

Grade, temperature and coating — how this part is specified

A complete specification names the grade (including the temperature suffix), the shape and dimensions with tolerances, the magnetization direction, the coating and the destination. With those five points YUECI KEJI quotes quickly; with any of them missing the project waits. Working temperature is set by the suffix, not by the shape, and the coating is set by the environment.

Designing the magnetic circuit and working on the line

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

When to choose a different shape

A disc is the default. Move to a ring when the part must mount on a shaft or let flux through the centre, to a countersunk disc when the magnet is also the mounting point, and to a block when a large flat pole area is worth more than a round one.

Where this material is typically used

Sintered NdFeB discs in this grade end up in automotive and industrial hot zones — sensors, actuators, fixtures and thermal-cycled assemblies that standard N52 could not survive.

Why buyers choose it

  • N52H Disc Magnet — built to your approved drawing, with grades, coatings and tolerances confirmed at quotation.
  • Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
  • Magnetization to drawing: axial through the face, diametric across the diameter, or radial for rotary sensing.
  • Coatings from bright Ni-Cu-Ni to non-reflective black epoxy for optical and medical builds.

Applications

Automotive sensors and actuators

Under-bonnet and hot-zone fixtures

Thermal-cycled holding assemblies

Buyer Questions

N52H Disc Magnet FAQs

What does the H suffix mean?

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Is N52H export Export documentation and licensing requirements are confirmed per shipment.?

Export classification is confirmed per shipment against the product composition and destination.

How much flux do I lose versus N52?

Very little — the H series trades a small amount of energy product for the coercivity that survives 120℃. In most hot-zone circuits the recovered stability is worth more than the few points of flux.

Request a quote for N52H