NdFeB

Neodymium Rod Magnet

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Rod / bar Axial along the length Custom diameter & length Coated to spec
Neodymium Rod Magnet - YUECI KEJI

Specifications

GradeN52
ShapeRod / bar
CoatingNi-Cu-Ni, Zn, Epoxy, Au (custom on request)
ToleranceDimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
MagnetizationAxial along the length
ApplicationsSensors and reed-switch targets, deep-bore and probe assemblies, retrieval and inspection tools
Lead timeProduction lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method.
MOQQuoted per inquiry
Export controlExport classification is confirmed per shipment against the product composition and destination.

What is an N52 rod magnet

Neodymium rod magnets are long, round sintered NdFeB sections with poles on the two ends. The rod is the shape for reaching into a bore, building a field along an axis, or making a probe that has to survive handling. YUECI KEJI supplies rods across the commercial grade range, ground to your diameter and length.

N52 magnetic performance

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Why choose N52

A rod is the axis-building shape. It carries the field along its length rather than across a face, which makes it the natural choice for reed and Hall targets, bore probes and any assembly where the magnet has to reach somewhere a disc cannot.

Shape, dimensional tolerance and magnetization

Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.

Surface treatment

Test conditions and reports are available on request.

Coating choice follows the environment: bright Ni-Cu-Ni for indoor and clean-room work, zinc for cost-sensitive volume, and epoxy where the part is handled, exposed to salt mist or must not glare. Bare NdFeB corrodes quickly, so every rod leaves the plant coated unless the brief explicitly calls for a phosphated or as-ground finish.

Typical applications

Neodymium rods end up in sensing and probe duty: reed-switch and Hall targets, deep-bore assemblies, retrieval and inspection tools, and shaft-mounted field sources where a ring would be over-sized.

Handling, storage and shipping

Sintered NdFeB is hard but brittle: it chips on impact and pinches fiercely when it snaps to steel. Parts ship in padded, magnetically shielded or spaced packing with keepers where the design calls for them, and air freight follows IATA packing instruction 902 with the field at the package surface measured before dispatch.

Axial versus diametric magnetization for rods

A rod can be magnetized two ways. Axial magnetization puts the poles on the two ends, building a field along the length — the choice for reed and Hall targets, bore probes and through-axis sensing. Diametric magnetization puts the poles on opposite sides of the cylindrical surface for side-acting duty such as encoders and flow or position sensors. YUECI KEJI orients the magnetization to your drawing.

Machining, threading and assembly

Rods are finished by grinding, not cutting, because sintered NdFeB is brittle and cracks under a saw or shear. Lengths are ground to your dimension and threaded ends or tapped holes can be specified; field cutting or drilling is not recommended and risks fracture. Tolerance is quoted per drawing rather than to a single fixed figure.

Field reach and length-to-diameter ratio

A long, thin rod carries its field further from the surface but at a lower peak surface field; a short, fat rod concentrates the field close to the face. The right ratio follows the duty — reach for a probe that has to find something at a distance, concentration for a close-contact holder — and YUECI KEJI discusses the trade with you when the part is specified.

Custom sizing, prototyping and order minimums

Every dimension, grade suffix, coating and magnetization direction is built to your drawing or reproduced from your sample. Samples and small batches come first, then volume; repeat orders are faster because the tooling and the inspection routine already exist. Minimum order quantities are quoted per inquiry against the geometry and the grade.

Grade, temperature and coating — how this part is specified

A complete specification names the grade (including the temperature suffix), the shape and dimensions with tolerances, the magnetization direction, the coating and the destination. With those five points YUECI KEJI quotes quickly; with any of them missing the project waits. Working temperature is set by the suffix, not by the shape, and the coating is set by the environment.

Designing the magnetic circuit and working on the line

A rod’s force falls with the square of the distance from its pole, so length matters more than diameter in most circuits. If the force target is missed, a longer rod usually beats a bigger one; if the envelope is fixed, stepping up a grade recovers flux in the same rod.

When to choose a different shape

A rod is the default for axial field work. Move to a cylinder when the section is short and stout, to a disc when the field is wanted across a face, and to a ring when the rod must pass over a shaft.

Where this material is typically used

Sintered NdFeB rods in this grade end up wherever field has to travel along an axis — sensors, probes, bore assemblies and shaft-mounted targets.

Why buyers choose it

  • Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
  • Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.
  • Axial magnetization along the length as standard, diametric on request.
  • Coatings from bright Ni-Cu-Ni to non-reflective black epoxy for optical and medical builds.

Applications

Sensors and reed-switch targets

Deep-bore and probe assemblies

Retrieval and inspection tools

Linear actuators and solenoid cores

Medical and optical instrument cores

Maker, research and prototyping builds

Locating dowels and holding pins

Flow, speed and position sensors

Buyer Questions

Neodymium Rod Magnet FAQs

What lengths can you supply as a single rod?

Everyday rods run from a few millimetres to around 100 mm in one piece; longer sections are quoted per inquiry and can be built up from stacked rods where the design allows.

Can rods be magnetized diametrically?

Yes. Diametric magnetization puts the poles on opposite sides of the cylindrical surface for side-acting sensor duty; send the sensing direction and we orient it to drawing.

Are neodymium rods export Export documentation and licensing requirements are confirmed per shipment.?

Export classification is confirmed per shipment against the product composition and destination.

Can rods be cut to length on site?

Not safely. Sintered NdFeB is brittle and a saw, grinder or shear will crack it; lengths must be finished by the supplier with coolant grinding. Specify the length you need rather than planning to cut later.

How should I mount a rod?

Press-fit it into a non-magnetic sleeve or housing, bond it with adhesive, or leave it loose in a bore depending on the assembly. Keep ferrous tools and parts clear during handling — a loose rod snaps to steel hard and can pinch.

What coating suits medical or optical builds?

A non-reflective black epoxy is common for optical and medical assemblies, with gold plating where the contact or appearance calls for it; biocompatibility and any regulatory requirement are confirmed against your specification.

Request a quote for N52