NdFeB
N50 Cylinder Magnet
N50 cylinder magnets carry near-top-grade flux in a stout round section for high-force sensing and actuation. YUECI KEJI grinds them to your diameter and length.
Specifications
| Grade | N50 |
|---|---|
| Shape | Cylinder |
| Coating | Ni-Cu-Ni, Zn, Epoxy, Au (custom on request) |
| Tolerance | Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation. |
| Magnetization | Axial / Diametric / Radial |
| Applications | High-force sensors and encoders, actuators and solenoid cores, couplings and shaft targets |
| Lead time | Production lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method. |
| MOQ | Quoted per inquiry |
| Export control | Export classification is confirmed per shipment against the product composition and destination. |
What an N50 cylinder magnet is
An N50 cylinder is a sintered NdFeB rod with poles on its two flat ends, sitting at the top of the commercial energy-product band just below N52. The cylinder is the shape you reach for when you need a compact axial field and a clean round profile for press-fit or potting.
At YUECI KEJI N50 cylinders are sintered, machined to length and diameter, coated, then magnetised axially through the ends. Diameter, length, grade and coating are all built to drawing.
Why N50 is the high-flux choice
N50 carries about the most flux a mass-produced sintered NdFeB can hold, so a given cylinder delivers more force than N48 or N45 at the same size. That makes N50 the right grade when the package is fixed and you need maximum pull or holding without growing the part. The cost step from N48 to N50 is small against the performance gain in a size-limited design.
Shape, tolerance and magnetisation
Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
N50-specific applications
N50 cylinders go where flux density is the bottleneck: servo and stepper motor rotors, precision linear actuators, magnetic couplings with a tight torque envelope, and high-sensitivity sensor biasing. When the part must stay small but the field must stay strong, N50 is the default.
Handling, storage and shipping
NdFeB is hard but brittle and strongly magnetic, so cylinders ship in magnetically separated, padded packing with pole pieces kept apart. Keep them dry or rely on the coating; N50 is more temperature-sensitive than ferrite, so avoid exceeding the grade's operating ceiling.
Custom sizes, grades and order minimums
Every diameter, length, grade and coating is built to your drawing or reproduced from a sample. Prototype quantities are supported and repeat orders are faster once tooling exists.
Specifying an N50 cylinder order
A complete specification names the grade (N50), the diameter and length, the magnetisation direction, the coating, the working temperature and the quantity. The exact temperature coefficient and grade window are confirmed on request.
Designing the magnetic circuit at N50
At N50 the circuit is flux-limited, not volume-limited: because the energy product is near the top of the band, gains now come from a tighter air gap and better soft-iron return rather than a bigger magnet. Watch the demagnetising field in high-temperature or reverse-bias duty.
When an N50 cylinder is the wrong shape
A cylinder is the default for axial end-pole duty with a round profile. Move to a block for a rectangular face, to a ring for a through-bore, and to ferrite when temperature or price beats flux density.
Where N50 cylinders are typically used
They end up in servo rotors, precision actuators, couplings and sensor biasing — the size-limited, flux-hungry work where N50's extra energy product earns its place.
Why buyers choose it
- N50 reaches an energy band close to N52 without the top-grade cost premium.
- Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
- Axial, diametric or radial magnetization cut to drawing for sensing duty.
- Coatings from bright Ni-Cu-Ni to non-reflective black epoxy for optical and medical builds.
Applications
High-force sensors and encoders
Actuators and solenoid cores
Couplings and shaft targets
Buyer Questions
N50 Cylinder Magnet FAQs
Why choose N50 over N52 for a cylinder?
N50 sits within a few MGOe of N52 at a lower cost and with easier processing. Choose N52 only when the force budget genuinely needs it.
Can N50 cylinders be magnetized diametrically?
Yes. Diametric magnetization puts the poles on opposite sides of the cylindrical surface for side-acting sensor duty.
Are N50 cylinders export Export documentation and licensing requirements are confirmed per shipment.?
Export classification is confirmed per shipment against the product composition and destination.
Request a quote for N50
You may also like



