Neodymium is a powerful magnet but a chemically vulnerable one. Left bare, it oxidises and can shed material in humid or saline environments. Selecting from the available neodymium magnet coating options is therefore a design decision, not a cosmetic one.
The short answer: pick the finish by environment
Nickel-copper-nickel (Ni-Cu-Ni) is the workhorse for indoor and general-purpose magnets. Zinc is a lighter alternative with decent corrosion resistance. Epoxy suits chemical, abrasive or rough-handling environments. Gold is reserved for electrical contact, biocompatible or high-purity applications where its conductivity and inertness justify the cost.
The coating is the barrier between the alloy and the world. Choose it from the worst condition the magnet will meet, not the typical one.
Why NdFeB needs a coating at all
The sintered NdFeB body is porous at a microscopic level and rich in reactive rare-earth content. In the presence of moisture and especially electrolytes, it corrodes through both surface oxidation and galvanic attack. A continuous, adherent coating stops the electrolyte from reaching the substrate.
- Bare NdFeB: not recommended except in sealed, dry, inert conditions.
- Coated NdFeB: the default for any real-world deployment.
Nickel-copper-nickel (Ni-Cu-Ni)
This is the most common finish: an underlayer of copper for adhesion and brightness, sandwiched between two nickel layers for hardness and corrosion resistance. It gives a bright, solderable, durable surface.
- Best for: indoor electronics, motors, sensors, general holding.
- Pros: hard, attractive, widely available, good adhesion.
- Cons: adds plating thickness; not ideal in strong salt spray without extra sealing.
Zinc (Zn)
Zinc plating is lighter and often cheaper than nickel systems, with good corrosion resistance for many atmospheres. It is a common choice where a thinner, more uniform layer is preferred.
- Best for: mild indoor-outdoor transitions, cost-sensitive runs.
- Pros: economical, reasonable corrosion protection, thinner build.
- Cons: softer and less wear-resistant than nickel; can show white rust in harsh humidity.
Epoxy
An epoxy powder or liquid coating forms a thick, continuous polymer barrier. It excels where chemicals, abrasion or rough handling would defeat a thin metal plating.
- Best for: food-grade and pharmaceutical equipment, chemical process, magnetic separators, outdoor rugged use.
- Pros: excellent chemical resistance, thick and forgiving, can be coloured.
- Cons: thicker build changes tolerances; can chip if struck; not a conductive surface.
Gold (Au)
A gold flash over a nickel base provides an inert, highly conductive, biocompatible surface. It is the premium option, used where the magnet makes electrical contact or sits in a medical or high-purity context.
- Best for: electrical contacts, implant-adjacent and laboratory devices, high-reliability electronics.
- Pros: inert, conductive, corrosion-proof, clean appearance.
- Cons: expensive; the gold layer is thin and relies on the nickel base for structure.
Matching the coating to the job
Indoor consumer and industrial
Ni-Cu-Ni covers the vast majority of cases: speakers, motors, closures, sensors.
Marine, outdoor and salt exposure
Epoxy or a heavy nickel system with sealed edges; for true marine duty, epoxy over a properly prepared substrate is the safer bet.
Food, pharma and chemical plants
Epoxy is preferred because it resists the wash-down chemicals and abrasion these environments impose.
Electrical and medical contact
Gold over nickel where conductivity or biocompatibility is specified.
Coating and tolerances
Every plating or paint layer adds to the part's dimensions. If you are working to a tight envelope, the coating thickness must be included in the drawing. Our standard dimensional tolerance is about plus or minus one percent, with precision grinding to about plus or minus 0.05 millimetre available on request, and the coating is applied after sizing.
Inspection and quality posture
A coating is only as good as its continuity. Salt-spray testing, thickness measurement and adhesion checks are part of a disciplined incoming and in-process routine. Our production is run under a quality management system aligned with IATF16949 and ISO 9001/14001/45001, so coating consistency is treated as a controlled process rather than a final touch.
How coatings actually fail
A coating fails in three ways: it is applied over a contaminated or rough substrate and loses adhesion; it is scratched or chipped in handling and lets moisture reach the alloy; or it is simply the wrong chemistry for the environment and degrades in the fluid it faces. The first two are process and handling problems, the third a specification problem. All three are preventable with the right finish choice and disciplined production.
Edge coverage deserves special attention. The cut edges of a ground magnet are the most exposed points, and a coating that is thin or discontinuous there is the usual entry point for corrosion. Specifying edge protection and verifying it in incoming inspection catches the most common failure before it reaches the field.
Specifying the coating on a drawing
Call out the finish by name and layer, for example 'Ni-Cu-Ni, overall, min 10 micrometre total', plus any colour or appearance requirement for epoxy. State the corrosion test the finish must pass, such as a salt-spray hours target, so the supplier and buyer agree on what 'good' means. Because every layer adds thickness, note the coated tolerance separately from the magnetised body tolerance so the part fits the assembly after plating.
Visual and adhesion inspection
A coating is only as good as its continuity, so a disciplined incoming check matters. A simple visual scan under good light catches bare spots and blisters; a tape-pull or cross-hatch test checks adhesion; and a salt-spray chamber verifies the corrosion claim over time. For critical programmes, sample these checks rather than assuming the plating line is perfect, because a single thin edge is enough to start corrosion.
Storing coated parts
Coated magnets should be kept dry and separated so their faces do not abrade each other in transit. Avoid piling bare plated faces together, which can scratch the finish and create the very entry point the coating exists to prevent. Simple partitioned packaging preserves the surface that protects the magnet.
Coating and the assembly method
The choice of finish also interacts with how the magnet is assembled. A plated, conductive surface can be grounded or shorted in an electrical design, while an epoxy or gold finish changes that behaviour, so the coating is part of the electrical plan, not just the corrosion plan. Tell the supplier both the environment and the assembly method, because the right finish for a press-fit steel housing can differ from the right finish for a bonded plastic insert.
Frequently asked questions
The finish questions buyers ask before they place an order.
What is the most common neodymium coating? Nickel-copper-nickel is the default for indoor and general-purpose magnets because it is hard, adherent and widely available.
Which coating is best for outdoor or marine use? Epoxy generally, because it forms a thick chemical-resistant barrier; a heavy nickel system can work but needs carefully sealed edges in salt spray.
Can neodymium magnets be left uncoated? Only in sealed, dry, inert conditions. In almost any real environment a coating is required to prevent oxidation and material loss.
Why use gold plating? For electrical contact, medical-adjacent or high-purity applications where conductivity and inertness justify the extra cost.
Does the coating change the magnet size? Yes, every layer adds thickness, so coating build must be accounted for in the tolerance, especially on tight-fitting parts.
Need a specific finish for a corrosive or contact application? Request a quote and our team will recommend the right coating and tolerance for your environment.