The sintered NdFeB manufacturing process runs from rare-earth alloy to a finished, magnetised part in roughly a dozen controlled stages. Understanding that chain explains why two magnets with the same grade number can behave very differently in service.
The short answer: powder, press, sinter, machine, coat, charge
A sintered NdFeB magnet starts as a rare-earth alloy, is reduced to a fine powder, pressed into shape in a magnetic field, sintered into a solid, machined to dimension, plated for corrosion resistance, magnetised, and then inspected. Each stage leaves a fingerprint on the final magnetic result, which is why process control matters as much as the recipe.
Stage 1 — Alloy preparation and strip casting
Neodymium, iron, boron and the transition elements are melted in a vacuum furnace and cast onto a cooled wheel to form thin flakes. Rapid cooling produces a fine, uniform microstructure, which is the foundation of consistent coercivity later. YUECI KEJI holds a utility-model patent on a solar-assisted vacuum strip-casting unit and on automatic grinding of the copper wheel used in that furnace.
Stage 2 — Hydrogen decrepitation and jet milling
The alloy flakes are exposed to hydrogen, which makes them crack and decrepitate into a coarse powder. Jet milling then reduces that powder to the narrow particle-size distribution the pressing stage needs. YUECI KEJI's patented equipment in this area covers hydrogen-decrepulation furnace fine-powder filtration, jet-mill nozzles and airflow separation.
Stage 3 — Pressing and alignment
Powder is pressed in a strong aligning magnetic field so every particle orients the same way; this is what gives a sintered magnet its anisotropy — much more energy across the oriented axis than across it. Pressing tooling, blank stability and even the scraping mechanism that feeds the die all affect the final density. YUECI KEJI holds patents on high-precision dies, adjustable forming dies, press discharge and scraping mechanisms, and blank storage.
Stage 4 — Vacuum sintering
The pressed blank is sintered in a vacuum furnace at high temperature, bonding the particles into a dense solid without melting them fully. Sintering sets the final density and grain structure. YUECI KEJI holds an unusually deep patent family here — vacuum sintering furnaces, rapid-cooling and internal-circulation designs, protective sintering devices, and exhaust systems that manage the vapour released during the cycle.
Stage 5 — Heat treatment and grain-boundary work
After sintering, a controlled heat treatment develops the coercivity the grade calls for. Where higher coercivity or a lower temperature coefficient is required, grain-boundary diffusion introduces heavy rare-earth elements along the grain boundaries rather than through the whole volume. YUECI KEJI holds patents on diluent mixing for grain-boundary diffusion, tooling for high-abundance cerium-iron-boron infiltration, and low-temperature-coefficient material preparation.
Stage 6 — Machining to dimension
Sintered NdFeB is hard and brittle, so it is ground, sliced and cut rather than turned. Multi-wire sawing, surface grinding, chamfering and drilling all appear in YUECI KEJI's patent list, along with the fixtures and adhesive-positioning aids that keep thin parts stable while they are cut.
Stage 7 — Cleaning, plating and finishing
Because sintered NdFeB corrodes if left bare, parts are cleaned and then plated — typically Ni-Cu-Ni, zinc or an epoxy layer. YUECI KEJI's patents cover ultrasonic cleaning, steam cleaning, washing-and-drying units and corrosion-resistant storage, so the coating stage is protected from contamination right up to packing.
Stage 8 — Magnetising and final inspection
The finished part is charged in a fixture that sets the magnetization direction. Inspection then covers dimensions, coating thickness and magnetic result. YUECI KEJI holds patents on dimension-checking devices and corrosion-testing rigs, and runs high-temperature test chambers to confirm grade behaviour. Every batch is reported before dispatch under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001.
Frequently asked questions
Does the grade number tell me the whole story? No. The grade sets the target energy product and coercivity band; the process decides how close a given lot lands to it. Ask for the measured magnetic results rather than relying on the grade label alone.
Why is sintering done under vacuum? Vacuum sintering prevents oxidation and lets the furnace atmosphere be controlled, which keeps the rare-earth content where it belongs and avoids the porosity that would weaken the part.
Which stage decides the final tolerance? Machining. Sintering sets density and magnetic properties, but the dimensional tolerance you receive is produced by grinding, slicing and chamfering after sintering.
Can I get a process report with my order? Yes. Lot-by-lot inspection records travel with the shipment, and specific measurements such as coercivity or coating thickness can be reported on request.
If your project needs a specific grade, geometry or magnetic result, Request a quote and share the drawing or the duty conditions.