SELECTION GUIDE

How to Choose a Neodymium Magnet Grade (N35-N52) | YUECI KEJI

Learning how to choose a neodymium magnet grade starts with one number: the N grade (N35 through N52) tells you the magnet's energy product and therefore its field strength, while the letter suffix (N, M, H, SH and so on) tells you the maximum working temperature.

The grade stamped on a neodymium magnet is not a brand or a quality score; it is a compact summary of performance. Understanding how to choose a neodymium magnet grade lets you stop over-specifying (and over-paying) while still hitting the field your design needs.

The short answer: match grade to field, suffix to heat

Choose the lowest N grade that delivers the required pull or flux, because higher grades cost more and are not inherently 'better' for every job. Then confirm the temperature suffix covers your worst-case operating temperature. A correctly chosen N40 can outperform a needlessly specified N52 if the N52 is the wrong shape or temperature class.

At YUECI KEJI we supply the full commercial range from N35 to N52 NdFeB grades, so the selection question is about fit, not availability.

What the N number actually means

The number after the N is the maximum energy product in MGOe. N35 is about 35 MGOe; N52 is about 52 MGOe. Higher numbers mean more magnetic energy in the same volume, which translates to stronger pull and a higher surface field.

  • N35-N38: economical, ample for many holding and sensor uses.
  • N40-N45: the common general-purpose band for motors and couplings.
  • N48-N52: high-energy grades for space- and weight-critical designs.

Remanence (Br) and coercivity both scale with grade, but so does sensitivity to temperature and to demagnetising reverse fields. Stronger is not automatically safer.

Remanence, coercivity and why grade is not the whole story

Two properties matter for a working magnet:

  • Remanence (Br): the leftover magnetisation after the field is removed; higher grade means higher Br and a stronger external field.
  • Coercivity (Hc): resistance to being demagnetised by an opposing field or by heat.

A very high N grade with low coercivity can be knocked down by a stray reverse field. That is why motor and sensor designers look at both numbers, not just the N value.

Temperature suffixes: the part after the N

The letter suffix indicates the maximum operating temperature class. Common designations include N (standard), M, H, SH, UH and EH, stepping up the thermal ceiling. As a rule, the higher the suffix, the higher the temperature the magnet tolerates before irreversible loss.

  • N: standard room-temperature service.
  • M / H: moderate-temperature motors and industrial gear.
  • SH / UH / EH: elevated-temperature and demanding duty cycles.

Always specify the suffix from your worst-case temperature, not your average. A magnet rated for 80 degrees Celsius that sits at 90 in a motor hotspot will lose performance over time.

A practical selection workflow

Step 1: define the field requirement

Start from the physics: what flux density or holding force does the application need at the working gap? This sets a floor on energy product.

Step 2: pick the lowest grade that meets it

Begin at N35 and move up only as far as the calculation demands. You save cost and reduce brittleness-related handling risk.

Step 3: set the temperature class

Take the highest temperature the magnet will see, add margin, and choose the suffix that covers it. This is non-negotiable for motor and under-hood use.

Step 4: confirm geometry and coating

Thin sections and tight tolerances may require a specific grade's machinability profile, and the environment sets the coating. For long, slender parts such as neodymium bar and rod magnets, grade choice also affects how the magnetised direction is achieved.

Examples by application

Loudspeakers and headphones

Moderate grades such as N40-N45 are typical, with the temperature class set by amplifier heat and enclosure conditions.

Spindle and servo motors

N42-N48 with an M or H suffix covers most industrial duty; high-speed or high-ambient designs move to SH.

Magnetic sensors and encoders

Small, stable fields favour N35-N42; temperature class follows the host device, often M or H.

Consumer holding and closures

N35-N40 uncoated-or-coated parts are usually sufficient and keep cost down.

Common mistakes to avoid

  • Specifying N52 by default 'to be safe' when N40 would meet the spec.
  • Ignoring the temperature suffix and discovering drift after field use.
  • Forgetting that coating choice interacts with the grade in corrosive service.
  • Treating grade as a quality label rather than a performance target.

When to ask for help

If you have a field target and an operating temperature but no finished design, share those two numbers. The grade and suffix follow directly, and the geometry can be iterated around them.

Reading a magnet datasheet

A proper NdFeB datasheet lists energy product (the N number), remanence, coercivity, maximum operating temperature and often a reversible temperature coefficient. The number you design from is the one tied to your actual duty: if temperature varies, the max operating temperature and coercivity matter as much as the N grade. Ignore the marketing and read the limits.

  • Energy product: sets how much field fits in the volume.
  • Coercivity: sets resistance to reverse fields and partial demagnetisation.
  • Max operating temperature: sets the safe thermal ceiling for the suffix class.
  • Temperature coefficient: tells you how much strength drifts with heat.

Grade-by-application quick reference

As a starting point rather than a rule: consumer closures and light holding sit comfortably at N35-N40; general motors and couplings at N40-N45; high-speed or elevated-temperature motors at N45-N48 with an M or H suffix; and space- or weight-critical designs at N48-N52 where the envelope is unforgiving. Always confirm the suffix against the hotspot temperature before locking the design, because the N number alone says nothing about heat.

The grade-to-price curve

Higher N grades cost more per kilogram and are more sensitive to both heat and reverse fields, so the price curve is not linear with performance. Moving from N40 to N45 is usually modest; moving to the very top of the range costs disproportionately more for a smaller gain. Specifying the lowest grade that meets the field is therefore both cheaper and often more robust, because you avoid the extra sensitivity of the highest grades without giving up function.

A simple prototype loop

If the field target is not yet backed by a finished design, build the loop as: estimate field, pick lowest candidate grade plus correct suffix, machine or order samples, measure on the real assembly, then adjust one variable at a time. This avoids the common trap of over-specifying on paper and discovering the magnet was stronger, hotter-rated and dearer than the product ever needed.

Frequently asked questions

The grade questions we hear most from buyers and design engineers.

What does the N number on a neodymium magnet mean? It is the maximum energy product in MGOe. N35 is about 35 MGOe and N52 about 52, so a higher number means more magnetic energy in the same volume.

Is N52 better than N35? It is stronger per volume, but not automatically the right choice. N52 costs more and can be more sensitive to heat and reverse fields, so the best grade is the lowest one that meets your field requirement.

What do the letters after the grade mean? They indicate the maximum operating temperature class. As the suffix advances (N, M, H, SH and beyond), the magnet tolerates higher temperatures before irreversible loss.

Can I supply any grade from N35 to N52? Yes. Our NdFeB range covers the full commercial band, and we help select the specific grade and suffix for your application.

Should temperature or strength drive the choice first? Temperature sets a hard limit via the suffix; strength sets the N number. Confirm the heat class first so the magnet survives, then pick the lowest N grade that delivers the field.

Ready to pin down a grade for your part? Request a quote and our team will recommend the right N grade and temperature suffix for your operating conditions.