Stepper Motors
Stepper Motor Magnets
Hybrid stepper rotors carry a ring of axially magnetized poles on one half and the opposite pattern on the other. YUECI KEJI supplies those arcs and rings, magnetized to pattern and matched to the rotor stack.
Why YUECI KEJI stepper motor magnets
A hybrid stepper rotor is built from two toothed pole pieces with an axially magnetized permanent magnet between them: one end north, the other south. The magnet sets the detent torque and the holding torque, and the pole pattern sets the step angle. Both have to be right before the rotor is assembled, because the magnet cannot be re-poled afterwards.
YUECI KEJI presses, grinds and magnetizes NdFeB rings and arcs for stepper rotors under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with magnetization direction and flux verified before the parts leave.
- Ring and arc rotors magnetized axially, north on one face and south on the other
- Pole count, skew and segment gaps set against your rotor drawing
- N35 to N52 grades with M and H classes for warm-running frames
- Dimensions to about plus or minus one percent so the stack-up holds the air gap
- Holding torque and detent data reported on request for first articles
What a stepper rotor asks of the magnet
The rotor magnet in a hybrid stepper does not produce torque directly. It polarizes the two toothed pole pieces so the teeth lock to the stator field at discrete angles. What matters is that the magnetization is uniform, axial and strong enough to saturate the pole pieces at every tooth. A magnet that is under-grade, or magnetized off-axis, shows up as lost holding torque and uneven step sizes.
The geometry is unforgiving. The magnet ring has to sit between two stacks of laminations, so its outer and inner diameters and its thickness all feed the same air gap. A few hundredths of a millimetre of thickness variation changes the axial gap, and with it the torque curve.
Rings, arcs and magnetization
Most stepper rotors take a full ring magnetized through the thickness. Where the rotor is segmented for assembly, or where the design wants the magnet to double as a spacer, arcs are used, supplied as a matched set with the segment count and skew agreed against the drawing. YUECI KEJI supplies both from the same NdFeB line, magnetized to pattern and measured per lot.
Grade choice follows the frame temperature and the duty. N42 and N45 cover most office and instrumentation steppers. M and H classes suit frames that run warm in continuous duty. Where the application is outdoor or humid, epoxy or nickel-copper-nickel coating protects the surface without changing the magnetic circuit. See the neodymium motor magnets range for the wider motor catalogue, and the motor grade guide for the selection logic.
From rotor drawing to matched set
Send the rotor drawing with pole count, skew, air-gap dimensions and the frame's operating temperature. YUECI KEJI confirms the geometry against pressing and grinding capability, recommends grade and coating, and returns a quotation with a schedule. First articles are measured for flux, dimensions and magnetization direction, and holding torque is reported where you can test it on your own fixture.
Specifications
| Material | Sintered NdFeB (N35 to N52, M/H classes) |
|---|---|
| Geometry | Rings and arc segments to rotor drawing |
| Magnetization | Axial through the thickness; pole pattern per drawing |
| Tolerance | About plus or minus 1%; tight-tolerance grinding on request |
| Coating | Ni-Cu-Ni, zinc or epoxy |
| Applications | Hybrid stepper rotors, printer and scanner head motors, instrumentation drives |
Buyer Questions
Stepper Motors FAQs
Can the magnet be magnetized after the rotor is assembled?
No. Hybrid stepper rotors are magnetized as parts and then assembled, because a finished rotor cannot be pulsed to pattern without demagnetizing the wrong poles. The pattern is set here before shipment.
Ring or arc, which suits a segmented rotor?
A ring suits a one-piece rotor. Arcs are used where the pole pieces are assembled around the magnet, or where the design needs the magnet to space the two stacks. Arcs are supplied as a matched set.
What sets the step angle?
The ratio of stator teeth to rotor teeth on the pole pieces. The magnet's job is to polarize them, so the pattern has to be axial and uniform rather than multipole.
Do you report holding torque?
Where you can share the fixture, yes. First articles are measured on your bench or ours and the values are recorded against the lot.
Building a hybrid stepper rotor?
Send the rotor drawing and the frame temperature. We will confirm pattern, grade and coating.
Get a Quote