NdFeB

N38UH Disc Magnet

N38UH Disc Magnet is supplied to your approved drawing; grades, coatings, magnetization direction and dimensional tolerances are confirmed at quotation.

N38UH Disc Axial / Diametric / Radial Export licence managed
N38UH Disc Magnet - YUECI KEJI

Specifications

GradeN38UH
ShapeDisc
CoatingNi-Cu-Ni, Zn, Epoxy, Au (custom on request)
ToleranceDimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
MagnetizationAxial / Diametric / Radial
ApplicationsHigh-temperature sensors and instrumentation, turbine and engine instrumentation, thermal-cycled fixtures
Lead timeProduction lead time and shipping transit time are quoted separately. The confirmed schedule depends on the approved drawing, quantity, documentation requirements, destination and shipping method.
MOQQuoted per inquiry
Export controlExport classification is confirmed per shipment against the product composition and destination.

What is an N38UH disc magnet

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

N38UH magnetic performance

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Why choose N38UH for hot duty

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Shape, dimensional tolerance and magnetization

Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.

Surface treatment

Test conditions and reports are available on request.

Coating choice follows the environment: bright Ni-Cu-Ni for indoor and clean-room work, zinc for cost-sensitive volume, and epoxy where the part is handled, exposed to salt mist or must not glare. Bare NdFeB corrodes quickly, so every disc leaves the plant coated unless the brief explicitly calls for a phosphated or as-ground finish.

Typical applications

N38UH discs end up in instrumentation and hot-zone sensing: turbine and engine instrumentation, high-temperature sensors, and fixtures that cycle between ambient and extreme heat.

Handling, storage and shipping

Sintered NdFeB is hard but brittle: it chips on impact and pinches fiercely when it snaps to steel. Parts ship in padded, magnetically shielded or spaced packing with keepers where the design calls for them, and air freight follows IATA packing instruction 902 with the field at the package surface measured before dispatch.

Custom sizing, prototyping and order minimums

Every dimension, grade suffix, coating and magnetization direction is built to your drawing or reproduced from your sample. Samples and small batches come first, then volume; repeat orders are faster because the tooling and the inspection routine already exist. Minimum order quantities are quoted per inquiry against the geometry and the grade.

Grade, temperature and coating — how this part is specified

A complete specification names the grade (including the temperature suffix), the shape and dimensions with tolerances, the magnetization direction, the coating and the destination. With those five points YUECI KEJI quotes quickly; with any of them missing the project waits. Working temperature is set by the suffix, not by the shape, and the coating is set by the environment.

Designing the magnetic circuit and working on the line

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

When to choose a different shape

A disc is the default. Move to a ring when the part must mount on a shaft or let flux through the centre, to a countersunk disc when the magnet is also the mounting point, and to a block when a large flat pole area is worth more than a round one.

Where this material is typically used

Sintered NdFeB discs in this grade end up in the hottest corners of instrumentation and sensing — the duty that no other commercial NdFeB grade survives.

Why buyers choose it

  • N38UH Disc Magnet — built to your approved drawing, with grades, coatings and tolerances confirmed at quotation.
  • Dimensional tolerances are confirmed against the approved drawing and depend on part size, geometry and finishing process. Please identify critical dimensions when requesting a quotation.
  • Magnetization to drawing: axial through the face, diametric across the diameter, or radial for rotary sensing.
  • Coatings from bright Ni-Cu-Ni to non-reflective black epoxy; high-temperature duty favours Ni or epoxy.

Applications

High-temperature sensors and instrumentation

Turbine and engine instrumentation

Thermal-cycled fixtures

Buyer Questions

N38UH Disc Magnet FAQs

When do I need UH instead of SH?

Available grades, temperature ratings and coatings are confirmed against your drawing and operating conditions at quotation.

Is N38UH export Export documentation and licensing requirements are confirmed per shipment.?

Export classification is confirmed per shipment against the product composition and destination.

How much flux do I give up versus N52?

A great deal — N38UH trades energy product for coercivity. It is chosen for thermal survival, not for peak force, and the circuit is designed around the lower flux.

Request a quote for N38UH