Brakes
Magnetic Brake Magnets
Eddy-current brakes slow a moving disc or drum by dragging it through a magnetic field, with no contact and no wear. YUECI KEJI supplies the NdFeB and ferrite magnet arrays those brakes are built from.
Why YUECI KEJI magnetic brake magnets
An eddy-current brake works without touching what it slows: a conductive disc or drum rotating through a magnetic field has currents induced in it, and those currents dissipate energy as heat. The braking force comes from the field the magnets produce, so the magnet array, its grade, its coverage of the disc face and its spacing, is the brake's tuning parameter.
YUECI KEJI presses, grinds and magnetizes NdFeB blocks, arcs and rings for brake arrays under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.
- Block, arc and ring magnets to the brake's pole-pattern drawing
- NdFeB for compact arrays; ferrite where cost and temperature dominate
- Alternating-pole arrays supplied as matched sets
- Dimensions to about plus or minus one percent so the air gap stays uniform
- Coatings for outdoor and high-temperature installations
What an eddy-current brake asks of the magnet
The brake's force depends on the field strength at the disc, the disc's conductivity and its speed, and on how the field is distributed. Alternating north and south poles across the disc face give a force that rises with speed and falls to nothing at rest, which is exactly the behaviour wanted on a dynamometer or a trainer. A uniform field, by contrast, gives a nearly constant drag. The pole pattern is therefore a design decision, made on the magnetizing fixture and the drawing before the parts are pressed.
Heat is the other constraint. The energy the brake removes ends up in the disc, but the magnets sit close to it and see radiant and conducted heat. The temperature class has to cover the worst-case braking event rather than the average duty, because a demagnetized magnet is a brake that quietly stops working.
NdFeB or ferrite
NdFeB gives the strongest field in the smallest volume, which suits compact brakes such as exercise equipment, small dynamometers and instrumented trainers. Ferrite gives a weaker field but costs less, tolerates higher temperatures and resists corrosion without plating, which suits large industrial arrays such as those on continuous braking systems. YUECI KEJI supplies both, and the choice is usually made on volume, temperature and budget rather than on field strength alone.
Where the choice turns on temperature behaviour, the temperature coefficient article explains how each material loses field with heat, and the ferrite magnet range covers the ceramic alternative in detail.
From pole pattern to array
Send the brake drawing with the disc diameter, the air gap, the speed range and the worst-case braking energy. YUECI KEJI confirms the geometry and the pole pattern, recommends material, grade and coating, and quotes with a schedule. First articles are measured as a set so the alternating pattern is symmetric about the axis.
Specifications
| Material | Sintered NdFeB (N35 to N52, M/H classes) or hard ferrite |
|---|---|
| Geometry | Blocks, arcs and rings to the pole-pattern drawing |
| Magnetization | Alternating-pole arrays; direction per drawing |
| Tolerance | About plus or minus 1%; tight-tolerance grinding on request |
| Coating | Ni-Cu-Ni, zinc or epoxy |
| Applications | Eddy-current dynamometers, trainers, continuous braking systems |
Buyer Questions
Brakes FAQs
NdFeB or ferrite for a brake array?
NdFeB where the brake has to be compact and the field strong; ferrite where the array is large, the disc runs hot or the budget is tight. Both are supplied to the same pole-pattern drawing.
Why alternating poles?
Because the pattern sets the force curve. Alternating north and south across the disc face gives a force that rises with speed and disappears at rest, the behaviour a dynamometer or a trainer wants.
What temperature class does a brake need?
One that covers the worst-case braking event, not the average duty. A magnet demagnetized during a hard stop is a brake that quietly stops working.
Can you supply the array as a matched set?
Yes. Sets are measured together so the alternating pattern is symmetric, which keeps the drag even around the disc.
Designing an eddy-current brake?
Send the pole pattern and the worst-case braking energy. We will confirm material and grade.
Get a Quote