Bearings

Magnetic Bearing Magnets

Active magnetic bearings replace rolling elements with a controlled field. YUECI KEJI supplies the radial and axial NdFeB rings and discs that carry that field, machined to drawing and magnetized as a matched set.

Why YUECI KEJI magnetic bearing magnets

A magnetic bearing holds a rotor in position with force generated between stator coils and permanent magnets. The magnets set the bias field, the standing field the control system works against, so their geometry, grade and magnetization uniformity decide how much force the bearing produces per ampere and how quietly it runs.

YUECI KEJI presses, grinds and magnetizes NdFeB rings, discs and segments for bearing stators and rotors under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with magnetic results recorded lot by lot.

  • Radial and axial ring geometries to your stator and rotor drawings
  • Radial, axial and multipole magnetization, verified pole by pole where the design needs it
  • N35 to N52 grades with M, H and SH temperature classes for warm-duty bearing cavities
  • Dimensions held to about plus or minus one percent, with tight-tolerance grinding where the air gap is critical
  • Matched-set supply: sets measured together so the bias field is symmetric about the axis

What the bearing asks of the magnet

The bias magnet is not a general-purpose part. Three properties matter more than raw remanence: the field it produces at the control gap, the uniformity of that field around the circumference, and stability under the temperature rise of a running cavity. A ring magnetized radially gives a field that points outward all the way around, which is what a radial bearing needs. A disc magnetized axially suits an axial thrust bearing. Multipole patterns, with alternating poles around the ring, are used where the control law wants a sinusoidal or trapezoidal force profile rather than a static bias.

Because force scales with the product of bias field and control field, small differences between magnets in a set show up directly as bearing asymmetry: more current drawn on one axis, uneven stiffness, and a whirl threshold lower than the design predicts. That is why matched-set measurement, and not only piece-part inspection, is part of the supply.

  • Field uniformity: the circumferential variation that sets force symmetry
  • Temperature class: chosen for the cavity's steady-state rise, not the ambient air
  • Geometry: inner and outer diameters control the gap where the force is generated
  • Stability: enough coercivity to hold the bias field through fault-current spikes

Shapes, grades and magnetization

Most bearing magnets are rings or arcs. Rings suit radial bearings and are usually magnetized diametrically or radially. Arcs are used where the stator is segmented for assembly or where the magnetic circuit is already split. Discs cover axial thrust bearings. YUECI KEJI supplies all three from the same NdFeB press-and-grind line, so a bearing project can take rings and discs from one source and one lot numbering scheme.

Grade choice follows the cavity temperature and the fault-current requirement. Base grades such as N42 or N45 suit cool, protected cavities. M, H and SH classes, N42M through N52SH, hold their field when the bearing runs warm, and the higher coercivity classes survive the reverse-field spikes a controller can produce during a power fault. Where the bearing shares a cavity with high-temperature machinery, SmCo rings are an alternative; see the SmCo magnet range for high-temperature work.

From drawing to matched set

Send the stator and rotor drawings with the air-gap dimensions, the pole pattern and the cavity temperature. YUECI KEJI reviews the geometry against pressing, grinding and magnetizing capability, confirms grade, coating and magnetization direction, and returns a written quotation and schedule. Sample approval comes first: the first articles are measured as a set for field uniformity, flux and dimensions before the production run is released.

Coating is normally nickel-copper-nickel. Epoxy is used where the cavity is humid or chemically aggressive. See the surface treatment services page for the coating options and what each one is tested against.

Specifications

MaterialSintered NdFeB (N35 to N52, M/H/SH classes); SmCo on request
GeometryRings, arcs, discs and segments to drawing
MagnetizationRadial, diametric, axial or multipole
ToleranceAbout plus or minus 1%; tight-tolerance grinding on request
CoatingNi-Cu-Ni, zinc, epoxy or gold on request
Supply formMatched sets with per-set measurement records

Buyer Questions

Bearings FAQs

Can you supply bearing magnets as matched sets?

Yes. Sets are measured together for flux, field uniformity and dimensions, and supplied with a per-set record, so replacements behave like the originals.

Which magnetization pattern does a radial bearing need?

Usually radial or diametric magnetization through the ring wall, so the field points outward all the way around. Multipole patterns are used where the control law expects an alternating field.

What happens to the bias field during a controller fault?

A fault can drive reverse current through the coils. Choosing a grade with enough coercivity, an H, SH or higher class, keeps the magnet's own field intact through the spike.

Is SmCo used in magnetic bearings?

Yes, where the cavity runs too hot for NdFeB. SmCo rings and discs are supplied with the export documentation that grade requires.

Planning a magnetic bearing project?

Send the drawings and the cavity temperature. We will confirm geometry, grade and magnetization.

Get a Quote