Actuators

Linear Actuator Magnets

Voice-coil actuators and solenoids turn current into a linear force, and the permanent magnet sets how much force comes out per ampere. YUECI KEJI supplies the NdFeB cylinders, discs and tubes those actuators are built around.

Why YUECI KEJI linear actuator magnets

A linear actuator, whether a voice-coil motor, a solenoid or a short-stroke positioner, works from the force between a current-carrying coil and a permanent field. The magnet fixes that field, so the actuator's force constant, its stroke and its efficiency all trace back to the magnet's geometry, grade and magnetization direction.

YUECI KEJI presses, grinds and magnetizes NdFeB cylinders, tubes, discs and rings for actuator cores and return paths under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, and reports the measured magnetic values lot by lot.

  • Cylindrical, tubular and disc geometries to the actuator's magnetic circuit drawing
  • Axial or radial magnetization, chosen against the coil geometry
  • N35 to N52 grades with M and H classes for warm-duty actuators
  • Dimensions held to about plus or minus one percent so the coil gap stays constant
  • Coating options for dry, humid or chemically active environments

What an actuator asks of the magnet

Three things dominate. First, the field in the gap where the coil moves: it sets the force constant, and it follows from the magnet's cross-section and length, not only from its grade. Second, field linearity: a voice coil is attractive precisely because force stays nearly proportional to current over its stroke, and that depends on a magnet long enough that the coil stays inside a uniform region. Third, thermal behaviour: the magnet sits close to a coil that heats when driven, so the temperature class has to cover the duty cycle rather than the idle state.

A common mistake is to maximize remanence and then lose the gain to fringing and to the steel return path. A well-matched circuit with a mid-grade magnet usually outperforms a top-grade magnet in a poorly shaped gap, because the gap and the return path are where the flux either concentrates or leaks away.

  • Force constant: set by the field in the coil gap, which follows the magnet's cross-section
  • Stroke: the magnet has to stay uniform over the coil's full travel
  • Duty cycle: the temperature class has to cover driven current, not standby

Shapes and magnetization

Solid cylinders magnetized along their axis are the classic voice-coil core: the coil slides over or sits beside the cylinder and the force comes out perpendicular to the axis. Tubes, cylinders with a bore, put the coil inside the field and shorten the actuator. Discs stack into multi-pole assemblies where a flat, short force is wanted. Rings and arc segments suit rotary-to-linear conversions and claw-pole circuits.

YUECI KEJI supplies these from the same NdFeB line that feeds the motor and speaker ranges, so an actuator project can draw cylinders, tubes and discs from one lot scheme. Where the actuator runs hot, H and SH classes hold the field; where the environment is humid, epoxy or nickel-copper-nickel protects the surface. The grade selection guide covers the reasoning in more detail.

From circuit drawing to batch

Send the magnetic circuit drawing, the coil dimensions, the target force constant and the duty cycle. YUECI KEJI checks the geometry against pressing and grinding capability, recommends grade, coating and magnetization direction, and quotes with a written schedule. First articles are measured for flux and dimensions before the run is released.

Specifications

MaterialSintered NdFeB (N35 to N52, M/H classes)
GeometryCylinders, tubes, discs, rings and segments to drawing
MagnetizationAxial or radial, set against the coil geometry
ToleranceAbout plus or minus 1%; tight-tolerance grinding on request
CoatingNi-Cu-Ni, zinc or epoxy
ApplicationsVoice-coil actuators, solenoids, positioners, valve actuators

Buyer Questions

Actuators FAQs

Axial or radial, which magnetization suits a voice coil?

Usually axial along the cylinder, with the coil sliding over the outside, because that puts the field across the coil sides where the force is generated. Radial magnetization is used where the coil sits in a bore.

Does a longer magnet always give more force?

Up to the point where the coil stays inside the uniform field region. Beyond it the extra length adds mass and cost without force, because the coil is no longer in the strongest part of the field.

What grade suits an actuator that cycles all day?

The temperature class matters more than the number. An H or SH class with a mid remanence usually beats a top grade in a warm, high-duty circuit, because it holds its field through the duty cycle.

Can you supply tube magnets with a bore?

Yes. Tubes are ground to drawing with the bore diameter and wall thickness specified against your coil.

Designing a linear actuator?

Send the circuit drawing and the duty cycle. We will confirm geometry, grade and magnetization.

Get a Quote