Data Storage
Hard Disk Drive Magnets
A hard disk drive positions its heads with a voice-coil motor and holds its platters with a spindle motor. YUECI KEJI supplies the small, tightly toleranced NdFeB parts both are built around.
Why YUECI KEJI hard disk drive magnets
Inside a hard disk drive, two small permanent magnets do the work that matters. A pair of rare-earth plates in the voice-coil motor swings the head stack across the platters in milliseconds. A ring magnet in the spindle motor holds the platters at speed. Both parts are small, both are tightly toleranced, and both sit inside a sealed cavity where a chipped edge or a stray particle is a reliability problem rather than a cosmetic one.
YUECI KEJI presses, grinds and magnetizes small NdFeB parts for data-storage mechanisms under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.
- Small plates and rings to the mechanism drawing, from a few millimetres up
- Tight-tolerance grinding where the head-to-platter geometry depends on it
- N35 to N48 grades with the temperature class the cavity needs
- Nickel-copper-nickel or epoxy coating, handled to keep edges chip-free
- Lot traceability against your part number
What a drive mechanism asks of the magnet
The voice-coil motor wants a strong, uniform field in a narrow gap, because the force that accelerates the head stack comes from the coil sitting in that gap. The spindle motor wants a ring whose field is symmetric about the axis, because asymmetry shows up as vibration the head has to ride through. Both parts are small enough that a fraction of a millimetre changes the magnetic circuit, so the tolerance conversation starts with the drawing rather than with a catalogue.
The cavity is also sealed and hot. A drive that runs for years at temperature needs a grade that holds its field and a coating that does not shed. Chips matter as well: a fragment inside a sealed drive is a head crash waiting to happen, so edge quality and handling are part of the specification rather than an afterthought.
Plates, rings and handling
YUECI KEJI supplies voice-coil motor plates and spindle motor rings in the N35 to N48 range, with the thickness and parallelism the mechanism needs. Coating is normally nickel-copper-nickel, and epoxy is available where the design calls for a thicker, more impact-tolerant layer. Parts are packed to keep edges protected in transit, because a chip that survives shipping can still fail inside a sealed drive.
The same small-part capability covers the speaker and wider NdFeB ranges, so a mechanism project can draw plates, rings and discs from one lot scheme. The coating options article compares the finishes and what each is tested against.
From mechanism drawing to lot
Send the mechanism drawings with the gap dimensions, the cavity temperature and the handling requirements. YUECI KEJI confirms the geometry, recommends grade and coating, and quotes with a schedule. First articles are measured for flux, dimensions and edge condition before the run is released.
Specifications
| Material | Sintered NdFeB (N35 to N48, M/H classes) |
|---|---|
| Geometry | Plates, rings and small discs to mechanism drawing |
| Magnetization | Axial or radial per drawing |
| Tolerance | About plus or minus 1%; tight-tolerance grinding on request |
| Coating | Ni-Cu-Ni or epoxy |
| Applications | Voice-coil head positioners, spindle motor rings, precision mechanisms |
Buyer Questions
Data Storage FAQs
How small can the parts be?
From a few millimetres across. Send the drawing and we will confirm what pressing and grinding can hold at that size before quoting.
Why does edge condition matter so much?
Because the parts live inside a sealed cavity. A chip that is invisible on the bench can come loose inside a drive and take a head with it, so edges are specified and inspected rather than left to chance.
Which coating for a sealed drive?
Nickel-copper-nickel is the default. Epoxy is used where the design calls for a thicker, more impact-tolerant layer.
Do you keep records for repeat orders?
Yes. Dimensions, grade and flux are recorded against your part number, so a re-order years later behaves like the original.
Developing a drive mechanism?
Send the drawings and the cavity temperature. We will confirm geometry, grade and edge spec.
Get a Quote