Drone Motors
Drone Motor Magnets
Drone motors spin fast and run hot in a small package, and every gram of magnet mass is mass the aircraft has to lift. YUECI KEJI supplies the NdFeB arcs those outrunner rotors are built from.
Why YUECI KEJI drone motor magnets
A drone motor is an outrunner: the bell, carrying the magnets, rotates around a fixed stator. The magnets are usually arcs, magnetized radially, and they have to survive high rpm, hot duty cycles and the occasional prop strike, all inside a bell that cannot grow. The magnet's grade, arc geometry and magnetization set the motor's KV and its efficiency at cruise.
YUECI KEJI presses, grinds and radially magnetizes NdFeB arcs for drone and model aircraft motors under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.
- Arc segments to the bell drawing, supplied as a matched set
- Radial magnetization, skew per rotor design
- N42 to N52 grades with H and SH classes for hot-duty frames
- Thin arcs with tight thickness tolerance so the air gap stays uniform
- Coating that survives assembly handling and vibration
What a drone motor asks of the magnet
Three demands collide in a drone bell. The motor wants a strong field, which argues for a high remanence grade. The airframe wants low mass, which argues for thin arcs. And the duty cycle, minutes of high-current climb followed by cruise, argues for a temperature class that holds the field when the windings are hot. The practical answer is usually a high-grade magnet in a thin, well-toleranced arc with an H or SH suffix, rather than the highest grade at a lower class.
Skew matters too. A skewed arc, one whose ends are offset rather than square, reduces cogging torque, which is what makes a drone motor feel smooth on the bench. The skew is set in the magnetizing fixture and in the grinding, so it has to be on the drawing before the parts are pressed.
Arcs, grades and coating
YUECI KEJI supplies drone motor arcs in the N42 to N52 range with H and SH temperature classes, radially magnetized and skew-matched to your rotor. Thickness is held tight because the air gap in an outrunner is small; the standard tolerance is about plus or minus one percent, with tight-tolerance grinding where the gap is critical. Nickel-copper-nickel is the default coating, and epoxy is used where the bell is humid or exposed.
The same arc line feeds the wider motor magnet range, so a drone project and a larger motor project can share one lot scheme. The motor grade guide covers how duty cycle and cooling pick the temperature class.
From bell drawing to matched set
Send the bell drawing with arc count, skew, air gap and the motor's continuous current and duty. YUECI KEJI confirms the geometry, recommends grade and coating, and quotes with a schedule. First articles are measured as a set for flux and dimensions, and KV is checked on your test stand before the run is released.
Specifications
| Material | Sintered NdFeB (N42 to N52, H/SH classes) |
|---|---|
| Geometry | Arc segments to bell drawing, matched sets |
| Magnetization | Radial; skew per rotor design |
| Tolerance | About plus or minus 1%; tight-tolerance grinding on request |
| Coating | Ni-Cu-Ni or epoxy |
| Applications | Multirotor and fixed-wing drone motors, model aircraft, small outrunners |
Buyer Questions
Drone Motors FAQs
Why radial magnetization for a drone motor?
Because the bell rotates around the stator: the field has to point outward through the air gap, which is what radial magnetization produces. Axial magnetization would put the field along the spin axis and the motor would not develop torque.
What does skew do?
It offsets the arc ends so the magnets engage the stator teeth progressively rather than all at once. The result is less cogging torque and smoother low-speed rotation, at the cost of a slightly more complex magnetizing fixture.
H or SH class, how do I choose?
Look at the continuous current and the cooling. A motor that cruises at two-thirds throttle in free air usually runs within an H class. Competition frames that pull high current for minutes at a time need SH.
Can you supply arcs as a balanced set?
Yes. Sets are measured together for flux so the bell is magnetically symmetric, which keeps vibration and current draw even across the axes.
Building an outrunner?
Send the bell drawing and the duty cycle. We will confirm geometry, grade and skew.
Get a Quote