Ferrite Audio
Ferrite Loudspeaker Magnets
Most loudspeakers ever built run on ferrite. YUECI KEJI presses and magnetizes the ring and segment magnets that give a driver its sensitivity, in the volumes audio manufacturing actually runs.
Why YUECI KEJI ferrite loudspeaker magnets
The loudspeaker is the largest permanent-magnet application in the world by volume, and most of it runs on ferrite. A ferrite ring or segment magnetized across its thickness gives a driver the field it needs to move a cone, at a cost that makes high-unit-count audio manufacturing possible. Where NdFeB is chosen for small drivers, ferrite remains the default for anything with room for a bigger magnetic circuit.
YUECI KEJI presses and magnetizes ferrite rings, segments and discs for loudspeaker drivers under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.
- Ring and segment magnets to the driver's magnetic circuit drawing
- Anisotropic grades for the strongest field per volume
- No plating; as-pressed or painted, ready for assembly
- Unit volumes from prototype lots to production runs
- Dimensions to commercial tolerance, about plus or minus one percent
What a loudspeaker asks of the magnet
A loudspeaker driver's sensitivity follows the field in its voice-coil gap: stronger field, more sound pressure for the same input. The gap is bounded by the voice coil's diameter and the plate thickness, so within a given driver size the magnet's job is to put as much flux as possible into that gap, and ferrite does it at a cost no other material matches. The trade is mass: a ferrite driver is heavier than the NdFeB equivalent, which is why NdFeB took the small-driver market and ferrite kept everything larger.
Consistency matters as much as strength. A batch of drivers built from magnets that vary in flux will vary in sensitivity, and a production line that has to sort drivers by measured output is a line that has lost money. Lot-by-lot flux records are part of the supply for that reason.
Rings, segments and volumes
YUECI KEJI supplies ferrite loudspeaker magnets as rings magnetized through the thickness for standard drivers, and as segments for drivers where the magnetic circuit is split for assembly. Both are anisotropic grades, supplied as-pressed or painted, and no plating is needed because the surface is already suitable for bonding into the driver's pot.
The ferrite ring and segment pages list the stocked geometries, and the NdFeB speaker magnet range covers the small-driver alternative. The speaker magnet size guide works through the gap, mass and sensitivity trade.
From driver drawing to volume
Send the driver's magnetic circuit drawing with the gap dimensions, the voice-coil diameter and the annual volume. YUECI KEJI confirms the geometry against pressing capability, recommends grade and finish, and quotes with a schedule. First articles are measured for dimensions and flux, and production is released against your part number so re-orders match.
Specifications
| Material | Hard ferrite (ceramic), anisotropic |
|---|---|
| Geometry | Rings, segments and discs to driver drawing |
| Magnetization | Axial through the thickness (radial on request) |
| Tolerance | Commercial about plus or minus 1% (tight on request) |
| Coating | As-pressed or painted; no plating needed |
| Applications | Full-range and woofer drivers, professional audio, automotive speakers |
Buyer Questions
Ferrite Audio FAQs
Why is ferrite still the default for loudspeakers?
Because it puts a usable field into the voice-coil gap at a cost that works in volume. NdFeB is stronger for its size, but ferrite wins wherever the driver has room for the larger magnetic circuit.
Rings or segments?
Rings for standard drivers, magnetized through the thickness. Segments where the magnetic circuit is split for assembly or where the pot design needs it.
How consistent is the flux from lot to lot?
Flux is recorded lot by lot against your part number, so a production line can rely on the drivers behaving the same without sorting by measured output.
Do the parts need coating before assembly?
No. They ship as-pressed or painted, and the surface bonds directly into the driver's pot.
Building loudspeaker drivers in volume?
Send the magnetic circuit drawing and the annual volume. We will confirm grade and finish.
Get a Quote