EDUCATION

What Is a Samarium Cobalt Magnet? High-Temperature Rare-Earth Magnets | YUECI KEJI

A samarium cobalt magnet (SmCo) is the rare-earth magnet you reach for when neodymium cannot survive the duty. Where NdFeB is the strongest magnet at room temperature, SmCo trades some of that peak strength for exceptional high-temperature stability and corrosion resistance.

A samarium cobalt magnet (SmCo) is the rare-earth magnet you reach for when neodymium cannot survive the duty. Where NdFeB is the strongest magnet at room temperature, SmCo trades some of that peak strength for exceptional high-temperature stability and corrosion resistance. This article explains what SmCo is, where it excels, and the one commercial caveat - export control - that buyers must plan around.

What samarium cobalt is

SmCo is an intermetallic compound of the rare earth samarium and cobalt. There are two principal families: the 1:5 type (SmCo₅) and the 2:17 type (Sm₂Co₁₇), the latter offering higher energy product and temperature capability. Like other rare-earth magnets it is produced by powder metallurgy - milling, pressing in a field, sintering and then magnetising - yielding a hard, brittle part.

Why SmCo is chosen over neodymium

Two properties set SmCo apart. First, its high-temperature behaviour: SmCo retains its field at temperatures where standard NdFeB would demagnetise, and it keeps performing well into the 200-300℃ range without the special temperature-rated chemistry that NdFeB requires for anything above 80℃. Second, its corrosion resistance: SmCo is far less chemically active than NdFeB and is frequently used with little or no coating, which simplifies assemblies that must stay clean.

Where SmCo is used

  • Aerospace and defence electronics and actuators that see wide temperature swings
  • High-temperature motors, generators and turbomachinery sensors
  • Vacuum and cryogenic equipment where outgassing or plating is undesirable
  • Medical and scientific instruments needing stable fields over temperature
  • Downhole, geothermal and other harsh-environment sensing

In each case the application pays a premium for a magnet that simply will not quit when hot or corrosive.

Trade-offs to accept

SmCo is more expensive than NdFeB, largely because of cobalt and lower production volume, and it is likewise hard and brittle. Its peak energy product is below the strongest NdFeB grades, so where temperature and corrosion are not the binding constraints, neodymium is the more economical answer. Treat SmCo as the specialist for heat and hostile chemistry, not the default for general duty. For the neodymium alternative, see the NdFeB magnet overview.

An export-control note buyers should know

Samarium cobalt magnets are subject to export and import licensing in a number of jurisdictions because of their strategic and defence relevance. Buyers should confirm the applicable controls for both the exporting and importing country before committing to a supply chain, and should expect suppliers to ask for end-use information. Planning for this early avoids costly delays once production is underway, and it is far easier to clear licensing before a shipment is due than to untangle a held consignment afterwards.

SmCo chemistry in brief

The 1:5 and 2:17 designations describe the atomic ratio of samarium to cobalt in the crystal. The 2:17 type generally offers the higher energy product and the better high-temperature behaviour, while the 1:5 type is the older, simpler chemistry. Both are produced by the same powder-metallurgy route as NdFeB, which is why their handling and finishing rules overlap even though their service envelopes differ.

Total cost of ownership

SmCo looks expensive on the magnet line item, but in a hot, corrosive or vacuum duty it can be the cheaper total solution once you account for the alternatives: a temperature-rated NdFeB plus coating plus the risk of failure, or an alnico that cannot supply the field. Evaluate SmCo at the system level, including the licensing step, before ruling it out on price.

SmCo and corrosion

Samarium cobalt is far less reactive than NdFeB, so in many environments it is used bare or with only a thin finish for insulation or appearance. That simplifies assemblies in food, medical and vacuum service where a thick plating would be a contamination risk or an outgassing source.

SmCo versus temperature-rated NdFeB

For hot duty the alternative to SmCo is a temperature-rated NdFeB series (H through AH). NdFeB wins on cost and peak strength; SmCo wins on the highest temperatures and on corrosion resistance without plating. The choice is usually settled by the exact service temperature and whether a coating is acceptable in the environment.

Handling and machining SmCo

Like other sintered rare-earth magnets, SmCo is hard and brittle and is finished by grinding, not cutting. Its value and its licensing status make careful handling and inventory control worthwhile, and the export-control step should be built into the procurement plan from the first enquiry.

SmCo in motors and generators

High-temperature motors, especially in automotive and aerospace drivetrains, use SmCo where the rotor runs hot and a coated NdFeB would be at risk. The magnet's stability lets the machine shrink and run harder than a ferrite design would allow, at a cost premium justified by the duty.

SmCo sourcing lead time

Because SmCo is a lower-volume material and carries licensing overhead, lead times can be longer than for NdFeB, and the export-control paperwork adds steps. Plan procurement earlier than you would for a commodity magnet, and keep end-use documentation ready so customs and supplier checks proceed without delay.

SmCo and the rare-earth supply

Samarium is a less constrained rare earth than neodymium in most markets, and cobalt brings its own pricing dynamics, so SmCo pricing does not track NdFeB directly. For programmes exposed to neodymium volatility, SmCo can sometimes offer a more stable cost path, though its absolute level is higher.

Designing with SmCo

The same rules that apply to NdFeB apply here - design from the demagnetisation curve at the working point, specify magnetisation direction and coating, and confirm the service temperature. The difference is that SmCo's temperature and corrosion headroom let you simplify the coating and skip the temperature-rated chemistry that NdFeB would need above 80℃.

Frequently asked questions

Is SmCo stronger than neodymium? At room temperature, the strongest NdFeB grades out-pull SmCo, but SmCo retains its field far better as temperature climbs, so it wins in hot service.

Does SmCo need a coating? Often not. Its corrosion resistance is good enough for many bare applications, though a thin coating may be added for insulation or appearance.

Why is SmCo more expensive? Cobalt content and lower production volume raise cost versus NdFeB, which is the price of its temperature and corrosion advantages.

Are there export restrictions on SmCo magnets? Yes, in many jurisdictions samarium cobalt magnets are controlled and require licensing; buyers should verify the rules for both ends of the shipment.

Which SmCo type should I choose, 1:5 or 2:17? The 2:17 type generally offers higher energy product and temperature capability, while the 1:5 type is the older, simpler chemistry; the choice depends on the exact field and heat targets.

If your application runs hot or corrosive and you need a magnet that will not demagnetise, Request a quote and share the service temperature and duty so SmCo or a high-temperature NdFeB series can be compared.