EDUCATION

What Is Magnetic Flux Density? B-Field Explained for Buyers | YUECI KEJI

Magnetic flux density is the quantity every magnet specification eventually reduces to, and it is also the quantity most often quoted in the wrong place. Here is what it measures and how to read it.

Magnetic flux density, written B and measured in tesla (T) or gauss (G), describes how much magnetic field passes through a given area. One tesla equals 10,000 gauss, and most magnet conversations happen in one or the other depending on whether the number describes a datasheet property or a field measured at a surface. Understanding which of the two is in play removes most of the confusion in magnet specifications.

Flux, flux density and the units

Magnetic flux is the total quantity of field leaving a pole, measured in webers. Flux density is that flux divided by the area it passes through, measured in tesla. A magnet's total flux does not change when you move a sensor closer or further away, but the density does: the same flux concentrated into a small pole face gives a higher reading than the same flux spread over a large one. That is why a small magnet can read higher than a big one even when the big one carries more total flux.

Three numbers that are often confused

  • Remanence (Br): the flux density inside the material itself after the magnetizing field is removed. It is a material property, measured on a hysteresisgraph, and it is what a grade designation such as N42 refers to.
  • Surface field: the flux density just outside the magnet's face, measured with a gaussmeter or Hall probe. It depends on the grade, the shape and what sits behind the magnet.
  • Working-point field: the field the magnet delivers in the actual air gap of your assembly. This is the number that decides whether the application works, and it is usually lower than the surface field because steel, distance and leakage all take their share.

Why the datasheet number is not the measured number

A grade such as N42 promises a remanence in a range, not a surface field. The surface field of a given N42 magnet depends on its length-to-diameter ratio, its coating, and whether it sits against a steel plate or in free space. Two magnets of the same grade and weight can read quite differently on a gaussmeter if one is a long rod and the other a thin disc, because the rod works at a higher point on its demagnetization curve.

How flux density is actually measured

Surface field is measured with a Hall-effect probe held against the pole face, which is what a gaussmeter does. Flux is measured differently: a coil is wound around the magnet and the meter integrates the voltage as the magnet is withdrawn, giving total flux rather than field at a point. Flux measurement is the more useful one for production control, because it is less sensitive to exactly where the probe was placed, while surface field is the more intuitive one for a bench check.

What to specify, and what to ask for

If your design depends on a field at a specific location, specify the field at that location and let the supplier work backwards to a grade and geometry. If your design depends on consistency from lot to lot, specify flux with a tolerance and let the supplier measure it. If you are comparing two quotations, ask which number each one refers to: a grade, a surface field, or a flux. They are not interchangeable, and a quotation that quotes one while you assumed another is the most common source of "the magnets are weaker than promised" complaints.

Gauss, tesla and everyday references

For orientation: the Earth's field is roughly 0.5 gauss. A fridge magnet reads a few hundred gauss at its face. A strong NdFeB disc can read several thousand gauss at its surface. An MRI scanner runs in the tens of thousands of gauss. An N42 magnet's remanence, by contrast, is quoted as 1.45 to 1.48 tesla, or 14,500 to 14,800 gauss, which is a property of the material rather than a reading you would take with a probe.

Frequently asked questions

Is a higher gauss reading always a better magnet? No. A higher surface reading can simply mean a smaller pole face. What matters for your application is the field at the place the application needs it.

Why does the same magnet read differently against steel than in free space? Because steel provides a low-reluctance return path that raises the magnet's working point, so more of its potential flux density is actually delivered. In free space, much of the flux returns through air without passing any useful gap.

Should I specify grade or flux? Grade for material identity and repeatability; flux with a tolerance when the application cares about consistency; field at a point when the design cares about a specific location.

Can flux density be measured without special equipment? Roughly, with a reference magnet and careful comparison, but production control needs a calibrated meter or fluxmeter. The field measurement guide walks through the practical method.

Comparing two magnets on paper? Send us both specifications and we will tell you which numbers are actually comparable.