EDUCATION

What Is a Magnetic Circuit? Reluctance, Air Gaps and Flux | YUECI KEJI

A magnetic circuit is to flux what an electric circuit is to current. Once you see the analogy, half of magnet engineering stops being mysterious.

A magnetic circuit is the complete path that magnetic flux takes from a magnet's north pole, through whatever surrounds it, back to its south pole. It is the magnetic equivalent of an electric circuit, and it explains why two magnets of identical grade and weight can perform completely differently depending on the shape and the steel around them.

The analogy to an electric circuit

Three quantities map across. Magnetomotive force (MMF), measured in ampere-turns, is the magnetic equivalent of voltage: it is what the magnet provides, and unlike a coil it is fixed by the material rather than by an applied current. Flux is the equivalent of current: it is what actually flows around the circuit. Reluctance is the equivalent of resistance: it is how hard the path resists carrying flux. Steel has low reluctance, air has high reluctance, and the flux divides between paths in the same way current divides between resistors.

Why the air gap dominates

The single most useful consequence of the analogy is this: air is a poor magnetic conductor, and a very short air gap can outweigh a long stretch of steel. A tenth of a millimetre of gap can consume more of the magnet's force than centimetres of a well-designed steel return path. This is why a magnet holding against a steel plate is far stronger than the same magnet holding through a painted or rough interface, and why closing even a small gap with a keeper changes everything.

Permeance coefficient, or where the magnet works

The ratio of the magnet's length to its effective area, together with the reluctance of everything around it, sets a number called the permeance coefficient. That number locates the magnet's working point on its demagnetization curve. A short, fat magnet in free space has a low permeance coefficient, works near the bottom of its curve, and delivers only a fraction of its potential flux density. A long, thin magnet, or one closed into a steel circuit, works much higher. This is why geometry is a magnetic specification: the same material, in a different shape, is a different magnet.

Leakage and fringing

Not all the flux that leaves the north pole arrives at the south pole through the intended path. Some leaks around the sides, and some fringes out of the gap and back without doing useful work. Leakage is usually a design nuisance rather than a fundamental problem, but it explains why measured assembly force is always lower than the sum of what the individual parts suggest, and why suppliers ask for the whole assembly drawing rather than just the magnet dimensions.

Practical consequences

  • Backing plates: a steel plate behind a holding magnet raises the permeance coefficient and can substantially increase pull, as long as the plate does not saturate.
  • Keepers: a soft-iron bar across a horseshoe magnet's poles closes the circuit during storage and prevents slow demagnetization from self-fields.
  • Shields: a shield works by offering a lower-reluctance detour than your protected volume, not by blocking anything. The shielding article covers this in practice.
  • Assemblies: a magnet bonded into a steel cup, as in a pot magnet, works at a much higher permeance coefficient than the bare magnet, which is most of why the assembly outperforms the magnet alone.

Frequently asked questions

Is a magnetic circuit a real circuit?It is a real path for real flux, but nothing flows in the sense of current. Flux exists around the path continuously; it does not circulate like charge.

Why does a magnet stick better to thick steel than thin steel?Thin steel can saturate, and once it does the excess flux has nowhere to go except back through air, which raises the effective reluctance of the whole circuit and lowers the working point.

Does the circuit change with temperature?Yes. Steel's reluctance rises with temperature, and the magnet's own properties change too, which is one reason hot assemblies lose force faster than the material's temperature coefficient alone would suggest.

Can I calculate my own circuit?At a useful level, yes, with finite-element software. At a rough level, the permeance-coefficient approach gives a good sanity check. Either way, send us the assembly rather than the magnet alone.

Want your assembly checked as a circuit rather than a part list? Send the drawing and we will review the whole path.