SmCo Motors
SmCo Motor Magnets
When a motor has to hold its torque at temperatures that would demagnetize NdFeB, samarium cobalt is the answer. YUECI KEJI supplies SmCo arcs, segments and rings for hot-duty motors.
Why YUECI KEJI SmCo motor magnets
Samarium cobalt holds its magnetization at temperatures where NdFeB has long since given up, commonly rated to 250 degrees Celsius and beyond with Curie points far higher still, and it resists corrosion without heavy plating. In motors that run hot by design, such as downhole tools, aerospace actuators, high-temperature pumps and automotive exhaust-side machinery, that combination decides the material before torque density is even discussed.
YUECI KEJI presses, grinds and magnetizes SmCo arcs, segments and rings for hot-duty motors under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and magnetic values recorded lot by lot and the export documentation each shipment requires.
- Arc, segment and ring geometries to the rotor drawing
- Temperature capability to 250 degrees Celsius and beyond
- Corrosion resistance without heavy plating
- Export documentation handled per shipment, as the grade requires
- Dimensions to about plus or minus one percent
When a motor needs SmCo
The decision is usually made by temperature. NdFeB with an SH suffix holds its field to around 150 degrees Celsius; UH and EH classes push higher but cost more and become brittle. SmCo starts where those grades stop, and it keeps its coercivity at temperatures that would permanently weaken a rare-earth magnet. It also resists corrosion far better, which matters in downhole and chemical-service motors where plating is a liability rather than a protection.
The trade is torque density and cost. SmCo's remanence is lower than NdFeB's and its material cost is higher, so a SmCo motor is larger and more expensive for the same torque. The choice is made when neither NdFeB nor ferrite can survive the duty, and at that point the comparison is not really about price.
Arcs, segments and documentation
YUECI KEJI supplies SmCo motor magnets as arcs, segments and rings, magnetized radially or axially to the rotor's circuit, with dimensions held so the air gap stays uniform. Finish is passivation, nickel-copper-nickel, zinc or epoxy on request. Export documentation and licensing requirements are confirmed per shipment.
Where NdFeB can survive the duty, the neodymium motor magnet range covers it, and the high-temperature NdFeB article sets out how far the rare-earth grades can be pushed. The SmCo magnet pages list the stocked geometries.
From rotor drawing to lot
Send the rotor drawing with the continuous operating temperature, the stray-field environment and the annual volume. YUECI KEJI confirms the geometry, recommends grade and finish, and quotes with a written schedule including the documentation each shipment requires. First articles are measured for dimensions and magnetic values before the run is released.
Specifications
| Material | SmCo (samarium cobalt), sintered |
|---|---|
| Geometry | Arcs, segments and rings to rotor drawing |
| Magnetization | Radial or axial per drawing |
| Tolerance | About plus or minus 1% (tight on request) |
| Coating | Passivation, Ni-Cu-Ni, zinc or epoxy |
| Applications | Downhole tools, aerospace actuators, high-temperature pumps, hot-duty servo motors |
Buyer Questions
SmCo Motors FAQs
When does a motor need SmCo instead of NdFeB?
When the rotor runs hot enough that even an NdFeB SH class loses its field. SmCo is rated to 250 degrees Celsius and beyond, and it keeps its coercivity at temperatures that would permanently weaken a rare-earth magnet.
What does SmCo cost more of?
Torque density and price. Its remanence is lower than NdFeB's and the material is more expensive, so the motor is larger and dearer for the same torque, which is the trade accepted when nothing else survives the duty.
Does SmCo need plating?
It resists corrosion well, so passivation is often enough. Nickel-copper-nickel, zinc or epoxy are available where the assembly calls for them.
How is export documentation handled?
As part of the order. Export documentation and licensing requirements are confirmed per shipment.
Designing a hot-duty motor?
Send the rotor drawing and the operating temperature. We will confirm grade and documentation.
Get a Quote