Audio

Headphone Magnets

Dynamic headphone drivers work like tiny loudspeakers: a coil in a magnetic gap, pushing a diaphragm. YUECI KEJI supplies the ring and disc magnets those drivers are built around.

Why YUECI KEJI headphone magnets

A dynamic driver, in a headphone, an earbud or an in-ear monitor, moves a diaphragm with a coil sitting in the field of a permanent magnet. The magnet sets the driver's sensitivity: how much sound pressure comes out for a given input, and how much of the amplifier's power is spent getting there. In a headphone the magnet also has to be small and light, because it sits on the ear.

YUECI KEJI presses, grinds and magnetizes NdFeB rings and discs for headphone and earphone drivers under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.

  • Ring and disc magnets to the driver's magnetic circuit drawing
  • Axial or radial magnetization, set against the coil geometry
  • N35 to N48 grades, with the temperature class the voice coil needs
  • Tight-tolerance grinding where the gap sets the sensitivity
  • Nickel-copper-nickel or epoxy coating

What a headphone driver asks of the magnet

The driver's magnetic circuit is a compromise between three things: the field strength in the gap, the mass of the moving parts, and the linearity of the field so the coil's force stays proportional to current. A stronger magnet raises sensitivity but adds mass to the diaphragm assembly and makes the gap harder to machine. Most designs settle on a mid-to-high grade in a small, well-shaped gap rather than the strongest magnet available.

Temperature matters less than in a motor, because a headphone voice coil runs warm rather than hot, but the coating and the edge condition still matter. These parts are assembled by hand into small housings, and a chipped edge is scrap.

Rings, discs and the gap

Ring magnets suit drivers where the coil sits inside the magnet's bore, the common arrangement in full-size headphones. Discs suit earbuds and in-ear monitors, where the assembly is flat. Both are supplied to the driver's magnetic circuit drawing, with the inner and outer diameters and thickness held so the gap stays constant part to part.

YUECI KEJI supplies these from the same NdFeB line that feeds the speaker magnet range, so a headphone project can draw rings and discs from one lot scheme. Where the driver is sealed or humid, epoxy coating protects the surface; nickel-copper-nickel is the default elsewhere. The speaker magnet size guide covers the trade between gap, mass and sensitivity in more detail.

From driver drawing to lot

Send the magnetic circuit drawing with the gap dimensions, the coil dimensions and the target sensitivity. YUECI KEJI confirms the geometry, recommends grade, coating and magnetization direction, and quotes with a schedule. First articles are measured for flux and dimensions before the run is released.

Specifications

MaterialSintered NdFeB (N35 to N48, M class)
GeometryRings and discs to driver drawing
MagnetizationAxial or radial per drawing
ToleranceAbout plus or minus 1%; tight-tolerance grinding on request
CoatingNi-Cu-Ni or epoxy
ApplicationsFull-size headphone drivers, earbuds, in-ear monitors

Buyer Questions

Audio FAQs

Ring or disc for a headphone driver?

A ring suits a driver where the coil sits inside the magnet's bore, the usual full-size headphone arrangement. A disc suits flat assemblies such as earbuds and in-ear monitors.

Does a stronger magnet always mean a louder driver?

Up to a point. Sensitivity rises with field strength, but so does the mass of the moving assembly and the difficulty of machining the gap. Most designs settle on a mid-to-high grade in a well-shaped gap.

What tolerance does the gap need?

Tight enough that the gap does not move part to part, because sensitivity follows the gap. Our standard is about plus or minus one percent, with tight-tolerance grinding where the drawing calls for it.

Can you supply coated parts ready for hand assembly?

Yes. Nickel-copper-nickel or epoxy, packed so edges arrive chip-free.

Developing a dynamic driver?

Send the magnetic circuit drawing. We will confirm geometry, grade and coating.

Get a Quote