Generators

Generator Magnets

Permanent-magnet generators trade brushes and slip rings for a rotor that carries its own field. YUECI KEJI supplies the NdFeB arcs, segments and rings those rotors are built from.

Why YUECI KEJI generator magnets

A permanent-magnet generator builds its excitation field into the rotor, which removes the slip rings and the field regulator and leaves a machine that is simpler to build and more efficient at part load. The rotor magnets, usually arcs or segments magnetized radially, set the open-circuit voltage and the machine's behaviour under load, so their grade, geometry and magnetization pattern belong to the generator's electrical design rather than to an accessory list.

YUECI KEJI presses, grinds and radially magnetizes NdFeB rotor magnets under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with flux and dimensions recorded lot by lot so a rotor can be rebuilt years later from the same records.

  • Arc and segment rotor magnets, supplied as matched sets
  • Radial magnetization with skew where the design calls for it
  • N35 to N52 grades with M, H and SH classes for warm-duty rotors
  • Dimensions to about plus or minus one percent so the air gap stays uniform
  • Lot records kept against your part number for repeat orders

What a PM generator asks of the magnet

Two regimes matter. At no load the magnet sets the open-circuit voltage: more flux, more volts, but also more iron loss in the stator. Under load the armature reaction pushes back, and a magnet with too little coercivity can be permanently weakened in the process. That is why grade choice is a compromise between voltage, iron loss and demagnetization margin, and why H and SH classes are common in machines that see overloads or short circuits.

The magnets also have to survive the rotor's own environment: centrifugal force at speed, and the temperature rise of a machine that is often enclosed. Thin arcs in a high-speed rotor need both mechanical margin and a temperature class that covers the duty.

Rotors, grades and records

YUECI KEJI supplies PM generator rotor magnets as arcs, segments or full rings, radially magnetized and matched to the rotor drawing. Skew is available where the design wants a smoother waveform. Coating is normally nickel-copper-nickel, and epoxy is used in humid or chemically active installations such as hydro or marine sets.

Because generators are rebuilt rather than replaced, the lot records matter: dimensions, flux and grade are kept against your part number, so a rotor can be re-magnetized or replaced years later with parts that behave the same. The tolerance and dimension standards article explains what the recorded numbers mean, and the motor magnet range covers the rotating-machine catalogue more broadly.

From rotor drawing to matched set

Send the rotor drawing with arc count, skew, air gap, speed and the machine's continuous and overload temperatures. YUECI KEJI confirms the geometry against pressing and grinding capability, recommends grade and coating, and quotes with a written schedule. First articles are measured as a set, and the open-circuit voltage is checked on your rig before the run is released.

Specifications

MaterialSintered NdFeB (N35 to N52, M/H/SH classes)
GeometryArcs, segments and rings to rotor drawing
MagnetizationRadial; skew on request
ToleranceAbout plus or minus 1%; tight-tolerance grinding on request
CoatingNi-Cu-Ni, zinc or epoxy
ApplicationsPermanent-magnet generators, hydro and marine sets, auxiliary power units

Buyer Questions

Generators FAQs

Why do PM generators usually take H or SH grades?

Because armature reaction under load, and short-circuit conditions, can push a reverse field through the magnet. A higher coercivity class keeps the rotor's field intact through those events.

Can a rotor be re-magnetized with your parts?

Yes, and that is the point of keeping lot records: dimensions, grade and flux are stored against your part number, so replacement arcs match the originals.

Do you supply full rings instead of arcs?

Where the rotor design allows a full ring, yes. Arcs are used where the rotor is assembled segment by segment, or where the ring would be too large to press.

What about very high-speed rotors?

Thin arcs at speed need both a temperature class and mechanical margin. Send the speed and the arc dimensions and we will confirm the geometry before quoting.

Designing a permanent-magnet generator?

Send the rotor drawing and the operating temperatures. We will confirm geometry and grade.

Get a Quote