Ferrite Motors
Ferrite Motor Magnets
Not every motor needs the strongest magnet available. YUECI KEJI presses and magnetizes ferrite arcs, segments and rings for the motors where cost, temperature and corrosion resistance matter more than peak torque density.
Why YUECI KEJI ferrite motor magnets
Ferrite, sintered barium or strontium ferrite and a ceramic rather than a metal, produces a weaker field than NdFeB, but it costs a fraction as much, tolerates far higher temperatures, and resists corrosion without plating. In motors that run hot, run continuously, or are built by the million, that trade usually wins: washing-machine drums, pump drives, fan motors, starter motors and a large share of the automotive small-motor population all run on ferrite.
YUECI KEJI presses and magnetizes ferrite arcs, segments, rings and tiles to drawing under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and flux recorded lot by lot.
- Arc, segment, ring and tile geometries to the rotor drawing
- Isotropic and anisotropic grades, matched to the motor's circuit
- No plating needed; as-pressed or painted on request
- Temperature capability well above NdFeB's base grades
- Dimensions to commercial tolerance, about plus or minus one percent
Where ferrite wins
Ferrite's field is a fraction of NdFeB's for the same volume, so a ferrite motor is larger or heavier for the same torque. What it buys is a magnet that survives a much hotter rotor, costs far less per part, and needs no corrosion protection. In a motor that has to hit a price point, or that runs in a hot, humid enclosure for years, those properties beat remanence.
The usual home for ferrite is the arc or segment rotor: washing machines, dishwashers, pump and fan drives, automotive auxiliaries, and starter motors. Rings suit outer-rotor designs and some generator rotors. Because ferrite is pressed rather than machined from a block, the geometry is set by the tool, so drawings with ground features need a conversation early.
Grades and geometry
YUECI KEJI supplies ferrite motor magnets in isotropic and anisotropic grades, magnetized radially or axially to the rotor's circuit. Anisotropic grades give the stronger, better-directed field and are the default for motors; isotropic grades suit simpler holding and coupling duties. Surface finish is as-pressed, painted or epoxy-coated on request, and no plating is needed because the ceramic does not corrode.
Where a motor genuinely needs NdFeB's field, the neodymium motor magnet range covers it, and the NdFeB versus ferrite comparison sets out the trade in detail. The ferrite segment and arc pages list the stocked geometries.
From rotor drawing to lot
Send the rotor drawing with arc count, air gap and the motor's continuous operating temperature. YUECI KEJI confirms the geometry against pressing capability, recommends grade and finish, and quotes with a schedule. First articles are measured for dimensions and flux before the run is released.
Specifications
| Material | Hard ferrite (ceramic), isotropic or anisotropic |
|---|---|
| Geometry | Arcs, segments, rings and tiles to rotor drawing |
| Magnetization | Radial or axial per drawing |
| Tolerance | Commercial about plus or minus 1% (tight on request) |
| Coating | As-pressed, painted or epoxy; no plating needed |
| Applications | Washing-machine and pump motors, fan drives, automotive auxiliaries |
Buyer Questions
Ferrite Motors FAQs
Why choose ferrite over NdFeB for a motor?
When the motor has to hit a price point, runs hot, or is built in volume. Ferrite costs less, tolerates higher rotor temperatures and needs no plating, at the cost of a larger or heavier magnetic circuit.
Isotropic or anisotropic?
Anisotropic for motors, because it gives the stronger, better-directed field. Isotropic suits simpler holding and coupling duties where direction matters less.
Does ferrite need a coating?
No. The ceramic does not corrode, so parts ship as-pressed or painted. Epoxy is available where the design calls for a specific surface.
Can you press a ground feature?
Ferrite is pressed to shape rather than machined, so ground features need an early conversation. Send the drawing and we will confirm what the tool can hold.
Designing a ferrite motor rotor?
Send the rotor drawing and the operating temperature. We will confirm geometry and grade.
Get a Quote