Alnico Sensing
Alnico Sensor Magnets
Before rare-earth magnets, instruments sensed the world with alnico. YUECI KEJI casts and sinters the alnico magnets that still serve meters, magnetos and temperature-stable sensing today.
Why YUECI KEJI alnico sensor magnets
Alnico, an aluminium-nickel-cobalt alloy, holds its magnetization across a temperature range no rare-earth magnet matches, from cryogenic cold to several hundred degrees Celsius, and its reversible temperature coefficient is among the lowest of any permanent magnet. That stability is why it stayed in service long after stronger materials appeared: analog meters, magnetos, tachogenerators and temperature-sensing assemblies still specify it when the reading has to stay put.
YUECI KEJI casts and sinters alnico magnets to drawing under a quality system aligned with IATF16949, ISO 9001, ISO 14001 and ISO 45001, with dimensions and magnetic values recorded lot by lot.
- Cast and sintered alnico to drawing, including slender and odd shapes
- Lowest reversible temperature coefficient of the common magnet materials
- Usable from cryogenic temperatures up to several hundred degrees Celsius
- High remanence with low coercivity, so the circuit is designed against demagnetization
- Bare, epoxy or nickel-copper-nickel finish on request
What a sensing circuit asks of the magnet
A sensing magnet's job is to deliver a field that does not move. Temperature drift in the magnet shows up directly as reading error, and that is where alnico earns its place: its reversible coefficient is around a hundredth of a percent per degree, an order of magnitude below NdFeB. It also works cold, which matters in aerospace and cryogenic instrumentation where NdFeB's low-temperature behaviour needs careful management.
The trade is coercivity. Alnico is easily demagnetized by a strong reverse field, so the magnetic circuit has to be designed to keep the magnet working on a safe part of its demagnetization curve, usually with a long magnet in a well-dimensioned circuit rather than a short one in a tight gap. Slender bar and rod shapes are the classic answer.
Shapes, grades and finish
YUECI KEJI supplies alnico sensor magnets as bars, rods, discs and blocks, cast or sintered to drawing. Sintered grades suit smaller parts and tighter tolerances; cast grades suit larger and more intricate shapes. Magnetization is axial along the length or through the thickness, set against the circuit. Finish is bare, because alnico resists corrosion well, with epoxy or plating available where the assembly needs it.
The alnico bar, disc and block pages list the stocked geometries, and the alnico overview covers the material's properties in full.
From circuit drawing to lot
Send the magnetic circuit drawing with the operating temperature range, the expected stray fields and the dimensional envelope. YUECI KEJI confirms the geometry and the working point on the demagnetization curve, recommends grade, shape and finish, and quotes with a schedule. First articles are measured for dimensions and magnetic values before the run is released.
Specifications
| Material | Alnico (Al-Ni-Co), cast or sintered |
|---|---|
| Geometry | Bars, rods, discs and blocks to drawing |
| Magnetization | Axial along the length or through the thickness |
| Tolerance | Commercial about plus or minus 1% (tight on request) |
| Coating | Bare, epoxy or Ni-Cu-Ni on request |
| Applications | Analog meters, magnetos, tachogenerators, temperature-stable sensors |
Buyer Questions
Alnico Sensing FAQs
Why does alnico survive in sensing when NdFeB is stronger?
Because sensing cares about stability, not strength. Alnico's reversible temperature coefficient is roughly a hundredth of a percent per degree, and it works from cryogenic cold upward, so the reading does not drift.
What is the catch?
Coercivity. Alnico demagnetizes easily under a reverse field, so the circuit has to keep it on a safe working point, usually a longer magnet in a well-dimensioned gap rather than a short one.
Cast or sintered?
Sintered suits smaller parts and tighter tolerances; cast suits larger and more intricate shapes. Send the drawing and we will confirm which the geometry needs.
Does alnico need plating?
Not usually. It resists corrosion well and ships bare, with epoxy or plating available where the assembly calls for it.
Designing a sensing circuit?
Send the circuit drawing and the temperature range. We will confirm shape, grade and working point.
Get a Quote